'78 15HP Evinrude starving for gas

budduggley

Recruit
Thread starter
Joined
Jun 18, 2011
Messages
4
The engine starts right up but at low speed I have to play with the choke to keep it running. At high speed it will run as long as I slowly squeeze the bulb. Filter on fuel pump is clean and I've just put a new carb kit in as well as fresh gas. Tried running with gas cap removed in case vent was plugged. Any ideas?
 

Rayzor

Petty Officer 2nd Class
Joined
May 5, 2007
Messages
172
Re: '78 15HP Evinrude starving for gas

I would take a hard look at your fuel line connectors for air leaks. I have found them in the past while squeezing the bulb and hearing it hiss from a leak. It wont hold a prime if there is any air getting in the line but you will be able to keep it running if you work the bulb. If that checks out prime the motor good and pull the fuel line. Put it in a jar and start it to check for the fuel pump pulsing gas. Thats my best guess.
 

Monte1961

Lieutenant Junior Grade
Joined
May 8, 2011
Messages
1,180
Re: '78 15HP Evinrude starving for gas

The engine starts right up but at low speed I have to play with the choke to keep it running. At high speed it will run as long as I slowly squeeze the bulb. Filter on fuel pump is clean andAt high speed it will run as long as I slowly squeeze the bulb. Filter on fuel pump is clean and I've just put a new carb kit in as well as fresh gas. Tried running with gas cap in as well as fresh gas. Tried running with gas cap removed in case vent was plugged. Any ideas?

As I read your post, A few things are going to have to be looked at. 1st. I have to play with the choke to keep it running.= low Idle circuit is plugged up. (Needs carb overhaul). 2.At high speed it will run as long as I slowly squeeze the bulb.= Carb is not supplying sufficient amount of fuel @ WOT. Float out of adjustment, or week fuel pump. Heres what I would check first. Pull fuel line of of carb and turn the motor over. Is the fuel pump pulsing fuel when you do this? Answer yes! Fuel pump ok. Answer no! Rebuild fuel pump or replace with new. I've just put a new carb kit in as well. Did you completely disassemble carb components including all jets, needle and seat, remove any core/welch plugs and allow carb to soak for 24hrs? Answer yes! If rebuilt right theres other issues. Answer no! Redo carb. If it has adjustable low speed jet. Seat and back out 1.5 turns. Then work between tiller handle and low speed jet until you achieve the lowest rpm in gear you can get. Once that is done, turn jet ccw 1/4 turn and thats it, your done. Post back results.
 

budduggley

Recruit
Thread starter
Joined
Jun 18, 2011
Messages
4
Re: '78 15HP Evinrude starving for gas

Okay, I did not soak for 24 hours...I just sprayed it with carb cleaner. I will have to buy new core plugs and do the soak. Do I need to remove the plastic needle bearing insert?
 

dew2

Senior Chief Petty Officer
Joined
May 6, 2010
Messages
674
Re: '78 15HP Evinrude starving for gas

Okay, I did not soak for 24 hours...I just sprayed it with carb cleaner. I will have to buy new core plugs and do the soak. Do I need to remove the plastic needle bearing insert?
The one on the lowspeed needle? Not really but the welchplug at its end on top of the carb yes.those are the idle fuel entrance 3 tiny holes.
 

budduggley

Recruit
Thread starter
Joined
Jun 18, 2011
Messages
4
Re: '78 15HP Evinrude starving for gas

FYI. I learned the hard way that the plastic parts should have been removed. They melted and I had to buy another complete rebuild kit to get the needle valve bearing.
 
Top