62 Johnson 75hp Super Seahorse won't shift forward

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
I just bought a 71 Glasspar Citation with a 1962 75hp Johnson Super Seahorse. Replaced lower unit oil and started it up in a tub, seemed good. Got it in the water today, motor runs beautifully but couldn't get it to shift into forward. It did go forward once from the ramp to the dock but never would shift into forward again. Toured the lake in reverse and went home. Found the shift wire knife connections under the hood and am getting 12v in reverse but only 1v in forward. Am going to take apart the control lever unit next and see what's up in the switching there. Seem like I'm on the right track? How can I rule out the solenoid? New to boat ownership, thanks.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
No solenoids in there , just electro magnets..----Take ohm reading from each wire at the connecters.----Green to ground and blue to ground.----Both should read the same,
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
If you only have one volt, you either have a problem with the switch in the control, or a wire problem between there and the motor.

OR a direct short between the knife connectors and lower unit. Ohms test will show that.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Connect a jumper wire directly between the battery and green wire leading to the lower unit. If you have forward now, it is not getting voltage from the shift switch.

Warning!! Do not shift control to reverse while you have that jumper connected. Better yet, disconnect and isolate the blue wire. If voltage gets to both wires at the same time while it is running, something will probably bust.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
So measuring the leads to the lower unit (disconnected from shift switch) I’m getting 8.6ohms from blue and only 0.6 from green, there’s obviously something wrong down there. How hard is it to get at the connection in the gear case. Is this something a shade-tree can do?
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Confession: I put valvoline high performance 80w90 in the gear box. It said it was good for marine use- now I be seen some posts saying that the electric shift units don’t like the viscosity and can create problems. I’ve seen posts on both sides of the issue on type C lube. Is it possible for the coil to be stuck because of oil? That wouldn’t account for the low resistance reading would it.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
You have to get that high viscosity oil out of there before proceeding. Drain it, then fill it with ATF and drain again. May require repeating. Then fill with lube specified for electric gear cases.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Thanks, will do. After drain and flush, can I test coil action with unit empty? Seems like it would be safe in a no-load state. I jumped the battery directly to the coil leads and got the prop to lock in reverse, wouldn’t lock up forward.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
It will still shift with the wrong oil !!!-------Sounds like a wire might be pinched and shorted out with that low resistance.----They are not that hard to work on.----Just nuts and bolts in my opinion.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Thanks, will do. After drain and flush, can I test coil action with unit empty? Seems like it would be safe in a no-load state. I jumped the battery directly to the coil leads and got the prop to lock in reverse, wouldn’t lock up forward.

How are you getting the prop to lock?
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
So I drained the hi-vis and flushed ATF through a couple of times and left it full of ATF and now I’m getting fairly normal readings, 8.6 on the good reverse coil and 7.5 on the forward coil. As far as locking the prop, when applying voltage by jumping off the battery I just spin the prop by hand and it locks. The forward coil is trying to lock under voltage as the prop spins much more freely after removing jumper.Any thoughts? Could I have ruined the coil with high-vis? Have no idea if it was working before I got it.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
So I drained the hi-vis and flushed ATF through a couple of times and left it full of ATF and now I’m getting fairly normal readings, 8.6 on the good reverse coil and 7.5 on the forward coil. As far as locking the prop, when applying voltage by jumping off the battery I just spin the prop by hand and it locks. The forward coil is trying to lock under voltage as the prop spins much more freely after removing jumper.Any thoughts? Could I have ruined the coil with high-vis? Have no idea if it was working before I got it.

The coils(just electromagnets) are sealed, unless damaged. The resistances are within spec When the forward coil is energized, you should be able to spin the prop clockwise(when viewed from behind) with little or no resistance. Rotating it counter clockwise, should reveal some drag/resistance then it should stop. Vice versa when the reverse coil is energized.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Energizing forward coil does put a drag on the prop. Reverse locks solid
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Anyone have an opinion on why the forward coil is sluggish, doesn’t lock? Does it make a difference to have the motor actually running? I’ve only been energizing from the battery.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Sounds like the spring or the tab on the forward wrap spring is broken.----Easy fix for me.----No need to have the motor running !----With 12 volts to green prop should lock when you turn counter clock wise.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
I don't see anywhere that you have removed the lower unit yet. Those electric cables leading down to the lower unit are rotted out on an awful lot of those motors. Last time I looked they were no longer available.
 
Top