62 Johnson 40HP no spark

Vanman62

Cadet
Thread starter
Joined
Jul 13, 2018
Messages
8
Hi,

I'm having trouble getting spark on my 62/63 Johnson 40hp RK25D.

I took the flywheel off to replace my retaining ring and followed this guide (http://www.outboard-boat-motor-repai...%20Tune-up.htm) to set up my OMC magneto. Still no spark. I disconnected what I assume are the kill wires as well as the fuel and again, still no spark.

I have replaced the spark plugs, plug wires, coils, and condensers. I cleaned the points off and set to 0.030 gap. I've also cleaned the flywheel magnets. I currently have the pull starter off, I don't believe this is affecting anything though. I'm sure I'm doing something wrong. If anyone has any idea, please let me know.

Thanks,

Cam
 

Vanman62

Cadet
Thread starter
Joined
Jul 13, 2018
Messages
8
I've tried .020, my manual and from what I understand factory spec is .030 for points.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
It has been indicated to you that point gap is 0.020" and that is absolutely correct here !!!
 

Vanman62

Cadet
Thread starter
Joined
Jul 13, 2018
Messages
8
I have tried .020, no luck, I will set back to that though if it works for others. Before I yank off the flywheel again, is there anything else that could be the problem?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
For the 40 years or so it has been 0.020" on that magneto.----No idea why you would try 0.030".----Do you understand that if points open too early or late then there will be no spark.-----Are wires from coils going to the correct set of points ?-----Post a picture of your magneto looking down on it.
 

Vanman62

Cadet
Thread starter
Joined
Jul 13, 2018
Messages
8
Ok buddy, set them back to 0.020". I've attached a picture of my magneto.
 

Attachments

  • photo295661.jpg
    photo295661.jpg
    1.5 MB · Views: 1

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
To me it looks pretty dirty . I would clean the points shiny bright and clean them with something like acetone. You may also consider new points.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I do not understand the term " buddy " on these forums.---I am giving you correct information based on some 50 years of outboard knowledge.
 

Vanman62

Cadet
Thread starter
Joined
Jul 13, 2018
Messages
8
I've got a set of new points on the way. I have cleaned the old ones the best I could with fine sandpaper and alcohol, but they're probably 50 some years old at this point. They should be doing their job though, they are moving properly. Apart from the points is there anything else that could be the culprit? I also have copper core spark plugs which are screwed into the coils, so I don't think those are the issue.
 
Last edited:

WimJall

Petty Officer 2nd Class
Joined
Jul 11, 2018
Messages
111
The last Johnson I had was a 70's it didn't have spark and it was a broken wire. Ohm the wire from the points to the coil.
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
CLEAN that magneto! Looks pretty grungy - when flywheel spins, oil and grunge can get on everything (including the points).
 

Vanman62

Cadet
Thread starter
Joined
Jul 13, 2018
Messages
8
Engine is on the boat. I cleaned the magneto up. I received a new set of points today, put them in and got spark on at least one cylinder. Thanks for everyone's help. One point only came with the base, so I'm still waiting for them to send me a new one.

Thank you.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
The black coil wires are pretty contorted. Appears to work OK on one side, so don't think I would move them until you try the new/complete set of points. (Moving the wire might break it.) But if you can't get spark, might take a look at the wire on the "bad" side.
 
Top