50esl72c no spark.

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
Hello. I have a 1972 50 horse that won't spark. I have load tested my battery and polished terminals. I have new battery cables and terminal connectors. New solenoid. Brand new coils and plugs. Brand new rectifier which I don't believe affects ignition but old one was no good which I know can lead to stator damage. Black with yellow wire disconnected from power pack to eliminate possible ignition switch problem. Motor cranks strong. Timer base wires check at 16 ohms between and no continuity to ground. Brown wire from stator to power pack tests 825 ohms to ground. When cranking voltage on Brown wire from stator tests 175 volts ac using a fluke meter which claims to measure peak voltage. Is my stator bad based on this number? According to the service manual I got from the library it looks like I need 300 to charge power pack. Thanks in advance. I have gleaned a lot of great info on this motor by reading these forums and I feel I'm close to success but don't wanna guess as the stator and power pack are both pricey. Cheers.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
load tested battery because of cranking issues? Might remove plugs to increase cranking speed. Disconnect the shorting switch. Test spark with an adjustable spark tester.
 

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
I load tested battery because It's a couple years old and i wanted to eliminate it as a problem. I have also tried starting with a battery Charger hooked up and set on the jump start setting to boost cranking amps. What is the shorting switch? Is it seperate from black with yellow wire that grounds out power pack when key is turned off? Thanks
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
round about way of suggesting it might not be cranking fast enough to generate spark. Shorting switches can misbehave and short the ignition -- one shown on your engines parts diagrams, but doesn't mean you have one. Still might try it with the plugs out and see if it cranks faster that way, testing spark with a spark tester. Using an adjustable spark tester is the only way to know what you have -- may be getting spark, but not enough to fire the engine if that's how you are testing.
 

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
Thanks I will try cranking with plugs removed. Also will try another battery Monday. Testing with a peak reading meter I'm getting nothing out of my power pack to coils. I suspect the stator due to the fact I had been running the motor not knowing the rectifier was bad. I know this can damage the stator. Can you tell me if removing the flywheel will affect timing or is flywheel keyed to driveshaft?
 

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
Just finished cranking motor with plugs removed. Measured 185 volts ac on Brown wire from stator. This was using a regular digital multi meter. Seems to be a slight increase in stator output versus having the plugs in and cranking. When cranking with the plugs in I was getting about 165 volts ac using the same digital multimeter. Are these numbers meaningful considering that I wasn't using a peak reading meter? Or can I simply divide by .707 to calculate my peak voltage. I know the power pack must be tested with a dva meter due to the instantaneous discharge but the stator output is constant and can be measured with a standard multimeter? Thanks
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Can't help you there Docks Hound, but output increase sounds encouraging. You may already be referring to this website (recommend it): http://www.ebasicpower.com/downloads/cditech/CDI-Troubleshooting_Guide.pdf Not my favorite sport, if sometimes necessary. Test for spark.

Flywheel removal and reinstallation is pretty foolproof. Lining up the keyway puts it in the right position for timing; tightening it down to specs holds the flywheel in place on the shaft.
 

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
Thanks for the link Oldboat. I have noticed that I can occasionally get spark on either cylinder but not consistently. If the power pack is faulty does it typically quit working entirely or can it occasionally output ?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
For intermittent firing, would think it's more likely low stator voltage or a bad timer base. But it's not my cup of tea.

You showed an increase in stator voltage by increasing cranking speed. If it were mine, I would first suspect a failing starter -- would consider pulling it apart and cleaning it and replacing brushes, or taking it to a shop for load testing and possible rebuilding. With a good starter and hot battery, would retest (think you should expect 7/16" spark on an adjustable tester if the system is working right). If still intermittent sparking (one or both), would suspect stator or timer base. If no spark, one or both, I would suspect the pack.

Hope this helps some....
 

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
Yes very helpful thank you! I think I should buy a DVA meter if I'm gonna continue to own a boat. That CDI troubleshooting guide really helped and I'm certain I'll have this thing running soon. Voltage reading between timer base wires and ground while connected to pack seem to be suspect. This seems to suggest pack but again I'm using a standard digital multimeter not DVA.Might just throw on a new power pack and see if that fixes things. If it doesn't I'll buy a fancy meter and pin point it between the stator and timer base. Local auto electric shop tells me my starter is good. Will let you know how it turns out.
 

Docks Hound

Cadet
Thread starter
Joined
Mar 25, 2016
Messages
7
Well new power pack arrived and has been installed. Fired right up. Thanks again for the CDI link and the help Oldboat! Now I'm in the market for a fuel pump rebuild kit and some warmer weather. Cheers
 
Top