40 HP Identification & Compatability

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Hey guys! I just picked up an old boat that has this 40 hp outboard on it. The guy I purchased it from could not give me a definite year on the motor. Unfortunately, the badge is worn-out and I need to I.D. this thing so I can find a lower unit for it. If you could help me identify the year and maybe tell me what would be compatible, I would greatly appreciate it. Thanks in advance!
 

Attachments

  • photo263754.jpg
    photo263754.jpg
    89.8 KB · Views: 0
  • photo263755.jpg
    photo263755.jpg
    90.8 KB · Views: 0
  • photo263756.jpg
    photo263756.jpg
    82 KB · Views: 0
  • photo263757.jpg
    photo263757.jpg
    60.2 KB · Views: 0
  • photo263758.jpg
    photo263758.jpg
    86.6 KB · Views: 0

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The cowling suggests a 1992 model.----Or perhaps a 1993.-----SO these lower units for a few years of that era were unique.-----Had to do with driveshaft spline diameter.---Take the lower unit off and measure that spline .-----If it is a short shaft it may be even a bigger challenge to find one.-----Your location is ?
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
No Title

I am located in Treasure Island, FL (Clearwater/Tampa area). The guy I purchased it from claimed it might have been a 95' -- which I doubted. I suspect that you are on the right path though -- this being a unique make. The guy claimed to have bought the boat because he had a lower that he thought would fit. For whatever reason, his lower unit did not fit. Here are some pictures of the lower -- I am not sure as to what I should be measuring. Also, is there a part # that I am missing? I cannot seem to find one on the lower. The reason I have chosen to seek out a new lower is because this guy has already tore into this unit. I know the shift rod is missing and who knows what else is absent. Pretty sure this prop is an incorrect size as well. I can wrench stuff down and reassemble. However, I am not familiar enough with outboards to notice missing parts or reassemble without dissembling if that makes any sense lol. I guess if I could identify the year, I could purchase a manual and attempt to rebuild. Here are some photos of the lower unit.
 

Attachments

  • photo263761.jpg
    photo263761.jpg
    44.2 KB · Views: 0
  • photo263762.jpg
    photo263762.jpg
    45.3 KB · Views: 0
  • photo263763.jpg
    photo263763.jpg
    41.9 KB · Views: 0

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Measure the diameter of the spline on the driveshaft.------I may then advise on the year to be searched for.------You may not get an answer instantly from me.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Looks to be a 1/2" spline. That said, I don't have any precision measuring tools e.g. calipers. That measurement was taken with a tape measure.
 
Last edited:

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Okay, so I just went and took a closer look at the badge on the motor. I can FAINTLY see some of the stippling. Is there any "trick" to getting this stippling to reveal? If so, I could pull the #'s from the badge -- probably.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Hurry and run to your local boat shop / dealer.-----Hopefully they have someone with experience who can instantly identify it .----Will be for a 3 / 4 year limited production for the smaller spline or the later bigger spline.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Unfortunately, the boat can't be moved at the moment and the outboard is mounted. : (
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
An experienced mechanic can identify your shaft spline in an instant.-------Take the lower unit / shaft to a shop !
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Okay, guys, I have decided to tear into this unit and do a rebuild/fix myself. This is not going to be an easy rebuild for a plethora of reasons. First and foremost, this unit has already been partly dissembled so who knows what is missing. I hope to have you guys with me as I go through the process of reassembly. I have certainly "identified" the issue with this lower. When removing the bearing housing from the drive shaft, I had a great deal of difficulty pulling it off -- it was "stuck". After lubing and tinkering for a couple hours I was finally able to remove the bearing housing. After removal shards of metal and bearing rollers dropped out. I'm assuming that this was the cause of failure. Therefore, I am in the process of identify missing/needed parts for order. After doing so I will be asking lots of questions, be prepared! P.S. the gear case is completely emptied -- shimming will be required fun! I removed everything because the bearings were scattered throughout the unit -- it had to be emptied.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
No Title

I haven't had the chance to clean parts yet but here are some photos. The gears actually look pretty good!
 

Attachments

  • photo263987.jpg
    photo263987.jpg
    88 KB · Views: 0
  • photo263988.jpg
    photo263988.jpg
    81.8 KB · Views: 0
  • photo263989.jpg
    photo263989.jpg
    62.1 KB · Views: 0

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
" look pretty good "----I am not sure I would agree with that assessment.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Well, I am certainly not a marine mechanic by any means. What are you seeing?
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
The gears do not look sheered to me. If these gears are "shot" I will likely part out this lower unit and purchase another. At the point, it is not worth the rebuild.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Post some pictures of bearings and bearing surfaces of the gears.----Post pictures of the upper thrust bearing or the pieces.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
Okay I am going to take more thorough photos of everything so you can get a good look at everything.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
I have the suspicion as well because of corrosion. You will see in the photos. be right back.
 

Greglous

Seaman
Thread starter
Joined
Apr 23, 2017
Messages
59
There are a couple obvious bad parts. In the second to last photo, you can see where the previous owner damaged the lower bearing housing (probaby by not using a puller for removal).




DSC00199_zpsftpt59hn.jpg


DSC00202_zpsh1eewerd.jpg


DSC00203_zpsdlp22sln.jpg

DSC00204_zps8aewih79.jpg

DSC00206_zps1c7sk7pb.jpg

DSC00210_zpss7bmgwsc.jpg

DSC00211_zpsmfwpbjvj.jpg

DSC00212_zpsjg9ei1dh.jpg

DSC00214_zpstu1lsrba.jpg

DSC00216_zpshitq0y28.jpg

DSC00217_zpsobwmtdfa.jpg

DSC00218_zpssibl2ab5.jpg

DSC00219_zpsube8kdxa.jpg

DSC00223_zpshvvv4hgz.jpg

DSC00226_zpshf2bbogr.jpg



DSC00235_zpskhfnyp3q.jpg DSC00237_zpsyrjcd6df.jpg



DSC00220_zpswnjqewfg.jpg
 
Top