25 hp johnson 1991

Part time trucker

Recruit
Thread starter
Joined
May 15, 2017
Messages
3
We have a "dead cylinder" and are confused about what to check next. Starts and runs (rough), 2 cyl, pull the top plug and it dies, pull the bottom plug nothing changes
1. Both cylinders have the same compression.
2. Both have the same color spark on the tester
3. We have swapped coils, plugs, and wires and it's always the top cylinder running the engine.

only has one carburetor, reed valve is horizontal. I am thinking it has to be fuel mixture between the carb and cylinder or spark timing to the second cylinder any ideas would be appreciated.
 

Part time trucker

Recruit
Thread starter
Joined
May 15, 2017
Messages
3
Also I suspected a possible vacuum leak between the reed valve and cylinder so I sprayed carb cleaner all over the engine while it was running (no change)
The engine is running dry while testing so it shouldn't be water contamination.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Have you done a spark test to make sure you have good spark on both cylinders? Do that first before you tear into the motor. My guess would be you have a bad powerpak thats why the problem stays on the top cylinder. You should also get a new waterpump for it running it dry will destroy the impeller. What is the compression in #s
 
Last edited:

valvebounce

Petty Officer 2nd Class
Joined
Mar 18, 2014
Messages
102
Sounds like you have a weak spark to the top plug.If the compression is equal,yet it runs rough,maybe the top piston has had a meltdown.
Had the same problem on a 3 cylinder Merc,one of the pistons had had a meltdown.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
The statement about water contamination and running dry has me baffled. Like flyingscott says, if you mean running with the lower unit neither immersed or on muffs, you smoked the impeller -- would need to replace that before any more testing as bits and pieces can end up anywhere in the cooling system. (Water contamination would be a fuel related issue -- condensation in the fuel tank, for example.)

guess I'm also not sure what is meant by same color sparks on a tester. You need an open air tester, and look for about half inch spark on each lead. Your drop cylinder test would seem to indicate that the bottom plug is not firing.

If in fact there is spark on only one lead, I agree with flyingscott -- problem is likely the power pack located under your flywheel. There's a small chance that you have a bad flywheel magnate, and that's easy enough to check -- see if your screwdriver sticks to the magnets. (Use a harmonic balancer puller to pull off the flywheel.)
 

valvebounce

Petty Officer 2nd Class
Joined
Mar 18, 2014
Messages
102
If you have run your motor dry on more occasions,you have probably overheated it.Running an outboard dry is a definate no no situation.
Whatever the problem turns out to be,you will need to clear your water passages and check the water pump and impeller,No point in a repair without making sure the you have a decent cooling water flow,or you will have the same problem over again.
If you have a decent spark on both cylinders,then I would suspect a partially melted piston.The spark will ignite the fuel in the cylinder with a bad piston,but as you say,it will cause rough running.
Overheating can cause a plug to fail,the extra compression and heat can damage the insulation,so you will probably need new plugs to make sure.
You seem to have replaced the ignition system,so apart from the plug damage,it is probably working ok.
Post your findings,it will help others.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Does spark jump a gap of 3/8" in air , yes or no?---Sounds like a crankcase compression issue if spark is equal.--And one carburetor feeds both cylinders.---- So not a carburetor issue.----Have you checked fuel pump diaphragm ??-----And yes if running without water to the pump you will need a complete pump kit before launching the boat !!
 

Part time trucker

Recruit
Thread starter
Joined
May 15, 2017
Messages
3
Both cylinders seem identical except pulling the bottom plug does nothing to the running

As for the running dry that's confusing everyone. Problem started in the water, moved to using "earmuffs" on the water hose, and then we removed the water to make sure water wasn't getting from the cooling system into the cylinder. Short runs while monitoring the engine temperature.

I have a spark tester round ceramic disk with alligator clip on 1 side pin for plug wire on the other generally if the spark is above yellow it's sufficient both cylinders are blue/purple.

Compression is 91 top, 92 bottom. It's a little low but should still run out.
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
If you ran it without water you destroyed the water pump impeller, you need to buy the complete kit before doing anymore work on the motor.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
That compression is VERY low. I have a 93 model mine reads 130 and it has been abused.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
We can help you if you answer.------------Does spark jump a gap of 3/8 " in open air , yes or no ??
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Any evidence of mess on top of cylinder block? Might indicate the top seal is shot, which would give low crankcase compression/vacuum.
 
Top