2000 Johnson 35hp not hitting top end speed

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
I noticed last year that my 3 cyl 35hp would intermittently cut in and out on the top end, almost like the loop charging was kicking in and out. This year it seems to be running at about 80% of top speed, and is not kicking into full speed at all. Any ideas on how to fix this?
 

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
Check for good spark on all cylinders. If that checks out maybe the carb needs cleaning or rebuilt. And have you checked the compression?
 
Last edited:

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Loop charging does not cut in and out.----Please review the concept of loop charging.-------Is the oil inhection in service on this motor ?-----It should have been removed and thrown away long ago.-----Run with a timing light to confirm spark at all speeds.-------And yes a compression test is important when you encounter problems.---Waterpump impeller looked at ?
 

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
I got rid of the oil injection long ago. Impeller is fine. Have new plugs, and will try new plug wires and clean out carbs. If not running better I'll take it to service by someone who knows what they're doing! Thanks
 

Silvertip

Honorary Supreme Mariner
Joined
Sep 22, 2003
Messages
28,772
No need to start buying parts that you "think" might be the problem. Run the boat wide open (on the water) until it begins to miss. Cut the engine immediately and now pull the plugs and check them. A plug that is not firing will be fuel and or oil coated while the others should be light to medium tan. That test alone will tell you which cylinder has the problem and very likely it will be ignition related and very likely NOT a plug wire or plug. A compression test will also prove or rule out if there is mechanical issue with the offending cylinder. A cheap spark tester from an auto store will also allow you to check spark intensity on all cylinders.
 

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
Thanks for the info. The motor doesn't cut out at all, it just doesn't develop the top end power that it used to. I can tell it is not running at full speed. Last fall it started doing this, and would occasionally "kick in" for a few seconds and accelerate, then go back to the lower running rate. Still starts, idles, and gets out of the hole as well as it always has, just doesn't develop the top end RPM's.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Read post # 3 ?--------------If you can solve the issue with money then you do not have a problem.-----Use the repair shop.
 

scout-j-m

Chief Petty Officer
Joined
Jul 31, 2009
Messages
643
If it indeed is an ignition problem you are much better off trying to fix it yourself, especially if you think it may be only happening at high speed. Mechanics aren't going to lake test your motor and troubleshoot it, they will just do what they can in a barrel at medium to low rpms where it is hard to diagnose and fix. A lot of mechanics just start replacing ignition parts until the issue goes away and then you get a bill out the roof that includes expensive CDI parts you didn't need plus labor.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The powerpack / CDI box on this motor is around $400.
 

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
Yeah, I'd rather settle for slower top end speed than spend hundreds - I'll let you know what I learn from plug wires and carb cleaning
 

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
Update: I cleaned out the carbs and replaced plug wires. Motor went back to last year's top end behavior, cutting in and out of top speed. Better. I tried taking the air silencer off so I could spray carb cleaner in while it was running fast, and the motor responded, running at top RPM's like it used to. Does this mean it is not getting enough air? I looked at replacement air silencers and it said the part was obsolete. Any input on what I should do? Can I run the engine without the air silencer?
 

scout-j-m

Chief Petty Officer
Joined
Jul 31, 2009
Messages
643
So it responded with higher rpms by just removing the silencer or did you also have to spray the cleaner into the throat too? Either way it shouldn't hurt to have it removed. It doesn't serve any purpose as an air filter or cleaner.
 

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
I sprayed cleaner into the throats of the carbs, it ran better but was still cutting in and out of top speed. When I ran it without the air silencer, it ran perfect. Then I put it back on and it cut in and out of top speed again.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,701
Spraying cleaner down the throats isn't going to do anything except clean the throttle plate, manifold, and the reed valves. You say it ran better when you were spraying the cleaner into it, was that with or without the silencer?
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,701
Are the nuts hold the carb to the engine snug? Any lines coming off the manifold cracked? Fuel lines and filter clean, including the filter in the tank? Fresh gas? If all these are good, you should consider pulling the carb for cleaning/inspection
 

Zavoral

Cadet
Thread starter
Joined
Apr 27, 2014
Messages
10
check on all these things. could it be a rich/lean thing, since when the air silencer is off it runs great?
 

scout-j-m

Chief Petty Officer
Joined
Jul 31, 2009
Messages
643
check on all these things. could it be a rich/lean thing, since when the air silencer is off it runs great?

I thought you said that even with the air silencer off, it required carb cleaner to get it to run at higher rpms like it should?
 
Top