2000 Johnson 25 bad solenoid?

Skiffrider1214

Recruit
Thread starter
Joined
Mar 14, 2018
Messages
5
Yesterday I went out on my boat, I won’t to go crank it over and the starter stopped engaging the fly wheel. No big deal a bolt came lose. I realigned the starter and retightned the bolt in the process of doing so a wire touched a wire and all of the sudden there was a spark at the battery. Not sure what happened. Anyways went to go and crank the motor over to test the starter and nothing, the motor doesn’t turn over at all. I charged up the battery and went to try it today I got one half turn out of the starter and then nothing. I then hooked jumper cables to the solenoid from my truck the starter engaged slowly with the fly wheel not close to enough to start the boat but it did turn it. I am so confused on what happened? Does this mean I need a new solenoid. I think the starter is fine. Why is the boat not turning over now? Everything else on the boat works! Thanks!
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Sounds offhand like the starter might be binding -- might check the mounting again.
 

Skiffrider1214

Recruit
Thread starter
Joined
Mar 14, 2018
Messages
5
Yeah but no click or anything? I even un hooked the starter from the fly wheel to see if it would free spin and tried it and it doesn’t work that way either.
 
Last edited:

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
A spark at the battery suggests a bad connection there. Check all the connections and wiring in that area.

Sparks near the battery are also dangerous as they can ignite the gases . A battery exploding in your face will spoil your day.
 

Skiffrider1214

Recruit
Thread starter
Joined
Mar 14, 2018
Messages
5
Why can I jump the solenoid and the starter cranks but it won’t crank with the key? is there a possibility it’s the solenoid
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Post # 1 talks about ---half turn from starter------I would take the starter apart for inspection.----That costs no coins.-----Some will argue that approach !
 

Skiffrider1214

Recruit
Thread starter
Joined
Mar 14, 2018
Messages
5
The started was working fine once I ran direct power to solenoid the motor cranked slow for this reason I think the solenoid is providing and insufficient amount of power to the starter. I ordered a new solenoid for 15 dollars
 

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
You say some current is flowing through the solenoid and turning the starter slowly. My experience with solenoids they are either good or bad. Meaning if bad then no amount current can pass through it.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Hard to follow your narrative — runs from a loose starter mounting bolt, to a shorted battery, to a potentially bad solenoid, to questions about the starter switch.

Did you reverse polarity when reconnecting battery cables? That would give you the sparking as well as prevent the starter from working. (It could also short out your rectifier, which may produce charging or tach issues.)

Is the replacement solenoid an outboard solenoid? (I’m not sure it’s a solenoid issue, btw, unless you shorted it out with a screwdriver blade when working on the mounting bolt.) Lesson is to disconnect the battery when doing anything (well, almost anything) at the engine.

To test the starter (essentially to bench test it), hook your known good battery directly to it — positive lead to post at the bottom of the starter; neg lead to the bracket. If it won’t crank the motor (plugs in) at 200 rpm or so, the starter needs to be disassembled and cleaned/rebuilt.
 

Skiffrider1214

Recruit
Thread starter
Joined
Mar 14, 2018
Messages
5
Okay so here’s what happened I bought a new solenoid, checked all fuses and connections cleaned everything up! I ran a test light when the new solenoid didn’t work, every time I turn the key to run, the NSS gets power, the two smaller wires on top of the solenoid also get power when I turn the key. The wire from the battery to the solenoid obviously has constant, BUT the wire from the solenoid to the starter gets 0 power. I checked the stud for the connection wire and checked the stud from the solenoid 0 power on either! But every other connection on the solenoid does have power :confused: Maybe I got a bad brand new solenoid?
 
Top