2000 H.O trim problem

2000 Stratos

Cadet
Thread starter
Joined
May 28, 2016
Messages
6
Hello all this is my first time at this so bare with me.

I am having a problem with my trim and tilt. The trim motor wants to run and cause the motor to go up by itself. It is on my 2000 Stratos. When hooked up to electrical I can use the manual descent and the motor will run down letting the motor into the lower position but as soon as I close the manual descent valve it automatically starts running back up to raise the motor. Does anybody have any idea where I can start looking. Thanks in advance
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
It could be a bad switch in the control handle. Or one of the T/T relays. Try swapping the relays once.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Post a model number. This will allow us to tell you where and which terminals to isolate so you can check for where the power is getting to the circuit. Most likely is a bad switch but a stuck relay could do it. If you swap the relays around and it wants to go down then replace relays, if it still wants to go up check for a short to hot in the blue wire or switch stuck. At some places in the circuit the up (blue) wire may have a stripe this is where model number would help.
 
Last edited:

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Do a little experimenting with above suggestions from boogie and I and reply. Then someone will explain how to isolate it from the boat side harness so you have an easier time determining where to start your search.
 

2000 Stratos

Cadet
Thread starter
Joined
May 28, 2016
Messages
6
Thanks gentlemen. The model number is J225HGLSSC. I had to have a new control box installed last week. I fished yesterday in the morning and went home around noon. Everything worked fine. I happened to walk by by boat later that day and noticed the motor all the way up. So now we have this. It's dark here now so I can try all possible ideas in the morning.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Perfect. Do boobies suggestion first but disconnect batteries in the meantime. Tonight
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Did this happen before the remote control was,replaced? Did you get brand new Oem , new aftermarket or used?
 

2000 Stratos

Cadet
Thread starter
Joined
May 28, 2016
Messages
6
I pulled the battery cable off as soon as I found it.

The shifter controll box is a new OEM bombardier.
 

2000 Stratos

Cadet
Thread starter
Joined
May 28, 2016
Messages
6
No the problem did not start before the control box was replaced. The shop that installed it didn't install correctly. I had to take it back due to the neutral lock out was not working. They told me after they fixed it that they had put some part in backwards. So it might be possible that they caused this when they took it out and fixed the neutral problem.
 

2000 Stratos

Cadet
Thread starter
Joined
May 28, 2016
Messages
6
Ok I swapped what I am thinking was the relays and motor still goes up. I unplugged the top connection below the relays and now the motor won't go up when battery is hooked up. Plugged the connection back to get her and motor goes up again. ?
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Take it back to the shop and tell them they pinched the tnt wires. Or
Open it up yourself, replace switch and cRefully route the three wires that are red green and blur
 

2000 Stratos

Cadet
Thread starter
Joined
May 28, 2016
Messages
6
Thats what I was thinking too. I'm not to sure how to remove the new shifter control box and all the trim. But I guess if I want to try to get on the water before the weekend is over I better try to figure it out myself.

The shift control box is a new BRP
 
Top