1996 Evinrude 90 one cylinder low compression

Brad_H

Cadet
Thread starter
Joined
May 18, 2016
Messages
7
I have a 1996 Evinrude 90 2 stroke that suddenly started running rough last fall. After trying several things I checked compression and got 125-130 in cylinders 2, 3, and 4, but only 60 in cylinder 1. I pulled the head hoping that there was a gasket leak but instead I found visible damage to a spot on the cylinder and a gouge in the cylinder as shown in the photos. The head gasket seems to look ok to me.
This is definitely not what I wanted to see. I assume there is no option other than tearing the engine apart? I have the shop manual which gives great detail for a complete engine rebuild, but I'm wondering what would be the minimum I would need to do to get this engine back in the water? It is a remanufactured power head purchased 2 years ago I think. I bought the boat last year and used it about 30 times before it had the problem. The engine seems to be in really good shape other than this problem.
I rebuilt the carbs before checking the compression (dumb, I know) and I did see some debris in one high speed jet, which I assume could have caused a loss of oil for this cylinder. I have worked on cars for many years and have lots of tools, but I've never rebuilt an engine. However, doing it myself may be my only option because I don't have the money to have it done professionally. Any guess on how much that would cost?

Thanks, Brad
 

Attachments

  • piston2.jpg
    piston2.jpg
    93.5 KB · Views: 2
  • cylinder2.jpg
    cylinder2.jpg
    297.8 KB · Views: 2

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Every one of these crossflow engines will suffer the same fate.----This failure is very common.-----Rebuild it with 4 WISECO pistons.-----Bore this block ?---Maybe , but I suggest finding a standard bore block to get it 0.020" over.----Then you will have a good engine for many years.---------Should be lots of those blocks around !
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Yep, that won't hone out. I used .030" oversize OEM pistons in my 90 hp rebuild going on 10 years ago now. If the other three holes are within tolerance, you can get away with a honing and new rings, with the fourth hole getting the oversize treatment. This only works if you're going with OEM piston. If you go aftermarket, it's better to go all four. Since budget seems to be a point with your project, you may be better off going for the one hole boring and new rings on the other three...
 

Brad_H

Cadet
Thread starter
Joined
May 18, 2016
Messages
7
Thanks for the info, I'm going to have to do this at the lowest possible cost so it sounds like boring out the one bad cylinder may be way to go. I'm trying to figure out how huge a job this is. Looking through the shop manual, pulling the power head doesn't look too bad and I would think I should be able to do that in a day.

But it's hard to tell from the manual what would be necessary beyond that because it gives all the steps for a complete rebuild of everything. What would be the basic steps to get the pistons out and the block ready for the machine shop? And would I need many special tools? I have all next week off work and am hoping I can make some progress.
Thanks! Brad
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
About the only thing I can think of that some people don't have in their tool box is a 12-point 5/16" socket to remove and replace the connecting rod bolts. Most everything else is pretty straightforward. Clean up any carbon you find in the ring grooves of the pistons you're re-using. If you don't have one, get a good torque wrench. And come on back here if you hit any snags!
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Looks like one of the rings has broken and is marking up the cyl liner. No point in re-using the current 3 ringsets. You might only get a few hours on the block when one of them might fail. Sk, when you overhaul, you will need to get 3 sets of new rings, and one oversize factory piston (which should come with the ringset on an oversize) You need to match the other 3 pistons, so get a factory and it will be made to weigh the same as the 3 standard pistons. You can get factory oversize pistons in .020 (5006658) and .030 (5006703) over. Hone the 3 cyls prior to re-assembly. You may find it economical to get a powerhead gasket set: 439085. Comes with all the gaskets, incl the head gaskets. Great catch on the debris in the high speed jet! Always good to clean all the carbs during the overhaul. Some also put in new thermostats at this time.
 

Brad_H

Cadet
Thread starter
Joined
May 18, 2016
Messages
7
Thanks for all the advice! So I guess I need to wait to get the cylinder bored out before I order the parts so I know what size piston I need, right?

I'm trying to figure out if there's anything I need to order now so next week when I'm on vacation I won't be stuck waiting on something I need to take it apart.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
What numbers / marking is on each piston now ?--And installing new rings in sloppy pistons would be a mistake if they are the factory style rings.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
That kinda looks like a Seizeco in there now...there is some kind marking on deflector.
 

James R

Commander
Joined
Feb 1, 2007
Messages
2,681
If you are going to the trouble of tearing it down do all four holes and make a new motor out of it. I use WSM pistons and gasket sets with great success. The problem,with wiseco, if you can call it such. is that you need at least .001" more bored out to allow for the extra expansion the wiseco pistons exhibit. WSM do .040 over if you need them.
 

Brad_H

Cadet
Thread starter
Joined
May 18, 2016
Messages
7
Well I finally got a day at home when it wasn't raining. I cleaned up the piston, Faztbullet was right there is a marking. Unfortunately it says "JE-734 040". Which means they are already .04 oversize, right? The piston below it had the same marking. I measured both cylinders with calipers and got 3.53" everywhere.
What are my options? Thanks, Brad.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
I believe Wisecos go as large as .064 oversize. As noted previously, all four pistons should at least be the same brand. Not a good idea to mix them up.
 

Brad_H

Cadet
Thread starter
Joined
May 18, 2016
Messages
7
Any idea where I would find a different block? Do you mean eBay or something, or one already ready to go from a marine engine place?
 
Top