1995 Johnson 60 hp wont start when hot

Lakeview305

Cadet
Thread starter
Joined
Aug 8, 2017
Messages
7
I have a 1995 60 hp Johnson that wont start after it has been running on the lake just fine. Engine starts cold at landing with no issues. When I turn motor off to use trolling motor the engine will turn over but not fire. I have replaced impeller, thermostat. Also to be noted the depth finder displays low voltage when I try to start engine after being turned off when its hot. I have check ohms of ignition components when cold and they are all reading correctly. Any ideas.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
What is your hot starting procedure?

What is your cold start procedure?

Please detail each.

Do you believe by ear that you are getting same cranking RPM hot and cold or does hot sound slower?

Answer these three and someone will tell you what next.
 

Lakeview305

Cadet
Thread starter
Joined
Aug 8, 2017
Messages
7
When I start it when its cold I pump ball, prime, and choke about 1/2 way. When its hot it will not start no matter what the procedure is. It sometimes may start for 30-45 seconds but then it will die again. I believe I have been getting same cranking RPM hot and cold. Also I connected depth finder directly to battery and depth finder still reads low voltage when I try to start the engine when hot. Usually when hot the engine turns over but wont start at all but sometimes it starts briefly then dies.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
What it your model #? When you say choke 1/2 way do you have a manual choke on this? Is it a tiller?
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
(Stator "35amp" Melt Down)
(J. Reeves)

The usual characteristic or sympton pertaining to an engine that has a stator melting down is that it will have spark when cold, but will have weak or no spark when hot. Many engines will run fine at first, but after being shut down, then attempting to restart 30 minutes or so later will not start. However, after sitting and cooling down, the engine may once more start and run. Eventually the stator will fail altogether resulting in no ignition/spark even when fully cooled.

This pertains mainly to the 35amp charging stator BUT this problem has also affected other smaller ampere stators. Make a note that the stator on engines manufactured in and after 1973 are two fold components. There are a series of smaller coils which deliver AC voltage to the rectifier, the rectifier converts that voltage to DC voltage to charge the battery. There are larger coils that deliver AC voltage to the powerpack capacitor in order to energize the ignition.

The 35 ampere stator has two (2) large black coils located (usually) at the rear of the stator. This 35 amp stator runs extremely hot and even though the water cooled voltage regulator/rectifier may be in perfect working order, this type stator will in time have what is called a "Melt Down". This is when those two large black coils start to drip a sticky substance down upon the timer base and the powerhead. The result is that the outgoing AC voltage to the powerpack capacitor drops, and this in turn results in weak ignition and eventually no ignition.

The smaller ampere stators since 1973 (2,3,4 cyl) have those larger coils but are sealed within a insulating ring... One at the extreme front, the other at the extreme rear of the stator (2/4 cyl) with the 3 cylinder models having (usually) three divided evenly within that sealed ring.

If a rectifier on any horsepower engine has failed (keeping it simple), this results in having the voltage back up at the stator causing the stator to overheat, which in turn causes a stator melt down.
 

Lakeview305

Cadet
Thread starter
Joined
Aug 8, 2017
Messages
7
Thank you all for your replies this is all great! I have been leaning towards the stator or powerpacks. The model number of the engine J60TLEOC and it is not a tiller I have a manual choke lever by my ignition. I am sorry If I my answers are vague, I am new to fixing boats as I have never had these specific issues before. THANK YOU ALL TREMENDOUSLY FOR ANY OTHER IDEAS ANYONE CAN OFFER.
 

Lakeview305

Cadet
Thread starter
Joined
Aug 8, 2017
Messages
7
Would the stator also explain why my depth finder reads low voltage when engine is hot and turned off?
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Would the stator also explain why my depth finder reads low voltage when engine is hot and turned off?

Sorry... I don't have a answer for that.

Is your tachometer acting normal and properly... or is it erratic, inoperable, whatever?

Is your charging system functioning properly... or is it problematic?
 

Lakeview305

Cadet
Thread starter
Joined
Aug 8, 2017
Messages
7
I believe my tachometer is working correctly, not sure if charging system is working. Seems problematic, how could I check it? It just seems when the engine is not starting and acting up the depth finder does as well. Voltage drops to about 10.8-11.1 when I try and start the boat after is has been sitting a while when its hot.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
If the tachometer was acting up, erratic, etc, there would be no question in your mind about it... the reading would be jumping all over the place, dropping to zero, flying up to an extreme, etc... or not working at all. This type problem raises its ugly head whenever a water cooled voltage regulator/rectifier starts going south.

The only way to judge the charging system is to have a volt meter installed... OR... hook a volt meter across the battery terminals (or the battery terminal wiring at some point) and make a note of its reading before starting the engine.... then to observe the reading as the engine runs.

It's normal for the voltage to drop somewhat when the electric starter is engaged as the starter is pulling a lot of amperage, current, voltage, whatever one wants to call it shouldn't drop excessively.... such as from 14.5v to 10v or 9v which could indicate a failing starter, battery, dirty cable end terminals, that sort of thing.
 

Lakeview305

Cadet
Thread starter
Joined
Aug 8, 2017
Messages
7
Okay I will look into all this. I am putting in new rectifier and stator this coming week. Hopefully it solves the no start when hot problem.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Why dont you do a spark check while it is hot and having the no start condition.
 
Top