1995 johnson 150 has water on spark plug

ssparkssparky

Recruit
Thread starter
Joined
May 8, 2016
Messages
3
I noticed today my motor wasn't running as smooth as before, pulled the plugs to check them and the top plug on the starboard side looks like its coated with milk. I still have 120 to 123 psi compression on all cylinders. Could the head gasket or o-ring be the cause of the water getting into that cylinder even if the compression is still good or is there other things that could cause this problem? I have also drained the carb to check for water and it had no water. Any help would be greatly appreciated!!!
 

Bosunsmate

Admiral
Joined
Apr 7, 2012
Messages
6,135
Yes it can still have a leak even with ok compression, replace the oring and check the thermostat while you are in there,
Be snappy about it as that water will of made its way through parts of the engine that need oil on them. They will rust out and pit relatively quickly if left sitting
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Can be coming if from the exhaust also. As suggested, it will quickly cause extreme damage if not tended to immediately. Or sooner if it is salt water.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Likely a leaker block...water entering cylinder from glue line as the o-ring rarely fails...
 

ssparkssparky

Recruit
Thread starter
Joined
May 8, 2016
Messages
3
If it is a leaker block what if anything can I do about it? Are you talking about it leaking from were the sealant is between the head and block?
 

James R

Commander
Joined
Feb 1, 2007
Messages
2,681
Faztbullet I could be wrong but didn't they cure the leaker block problem by 95.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Faztbullet I could be wrong but didn't they cure the leaker block problem by 95.
Leakers was never cured but slowed down after 1998.Ihave had several 99n and 2000 models leak.
If it is a leaker block what if anything can I do about it? Are you talking about it leaking from were the sealant is between the head and block
Check the simple stuff first and if it is a leaker it will need torn down,sleeve/s pulled ,block welded and resleeved to repair it.The problem is this is a lost cast block and where they glued Styrofoam block mold together the aluminum casting is thin and eventually cracks due to expansion fatigue.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Here is C&P from old Mar-Fab bulletin.....
PROBLEM:
Internal water cavity leaking into #1 cylinder.
Engine: 1991 & up carbureted 150/175 HP 60 degree V-6 Evinrude and Johnson outboards
Description: Approximately 25% of the 6V-6 blocks we test will show a leak into the #1 cylinder from the center water cavity underneath the regulator/rectifier. In certain cases, a leaking engine may develop a knock at around 3500 rpms. The sparkplug may also show signs of water, and the cylinder head?s combustion chamber, piston dome, and/or exhaust port may show signs of being steam cleaned by water. It is important to notethat some engines in the early stages of leaking may not show the mentioned symptoms and can only be detected by
pressure testing the block.
Cause: The leak develops from a thin section in the block.Due to engine vibration, varying pressures, expanding and
contracting, the aluminum cracks over time and causes water to leak from behind the sleeve.
Repair & Results: MarFab can provide its dealers with a remanufactured block or powerhead, or can repair the leaking
block by welding and re-sleeving.MarFab has been repairing 6V-6 leaker blocks since early
2002. Blocks are pressure tested after all work is performed to ensure proper repair has been made.
Limited Warranty: MarFab warranties its 6V-6 powerheads, blocks, and repairs for 1 year from date of purchase and/or repairs against
water leaking into #1 cyl from area discussed above.MarFab?s warranty is limited to repair or replacement of block only
 
Last edited:

James R

Commander
Joined
Feb 1, 2007
Messages
2,681
Hi Faztbullet. Great piece of information. Saturn was a customer of mine back aways and they had a similar problem with the lost foam process.
Thanks for the update.
 

ssparkssparky

Recruit
Thread starter
Joined
May 8, 2016
Messages
3
Thanks for all the info. Sounds like faztbullet's really knows his stuff. I ordered the o-rings in hopes of getting lucky. I have a 1986 johnson gt 200 I may have to put on it. Are those overall good engines? I did a compression test on it a while back and they were all around 100 with engine cold. Someone told me they were low compression engines. The 200 caught on fire with the previous owner and melted a couple of the carbs. I don't know how the fire started , if it was something he did or something that went wrong with the engine.
 
Top