1992 Johnson 200 boggin down problem

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
My Johnson is giving me such a hard time running. I can get her started after about 30 trys cold. Once I let her run a bit I try to increase speed and it boggs down. After several trys and my wife getting on the front deck the boat will get on plane. I've read other posts but it seems I've only done part of whats needed. I did take it to a mechanic who said the vro is the problem. I replaced the pump and disconnected the vro and the oil pump and now premix everything. But she still has a problem taking off and getting on plane. It sounds like i have two problems but the fact is the prop is the right size and pitch. Not sure what else to do. I could really use some ideas!!!
 

Jayrock

Petty Officer 2nd Class
Joined
Dec 19, 2008
Messages
132
Re: 1992 Johnson 200 boggin down problem

My Johnson is giving me such a hard time running. I can get her started after about 30 trys cold. Once I let her run a bit I try to increase speed and it boggs down. After several trys and my wife getting on the front deck the boat will get on plane. I've read other posts but it seems I've only done part of whats needed. I did take it to a mechanic who said the vro is the problem. I replaced the pump and disconnected the vro and the oil pump and now premix everything. But she still has a problem taking off and getting on plane. It sounds like i have two problems but the fact is the prop is the right size and pitch. Not sure what else to do. I could really use some ideas!!!

Do a compression check. It will help to eliminate the obvious... post the results
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
Re: 1992 Johnson 200 boggin down problem

How long has the mtr been doing this? Is it a new prob or what? Need a little history.
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

Boat actually started this two years ago. It would start dying out while trying to get her on plane. I check the fuel filter and the like and it seemed to do ok. 2 real problems are this. When I try to rev her up to get onto plane she boggs down and wont go any faster to get on plane.I have to do this like 5 or 6 times before she will start to get on plane. I though it was the VRO pump so I switched it out. It is a new pump just not the newest edition of it. But it seems to work fine. Now she will still bog down as you try to get on plane. But if I have my wife sit on the front of the deck she will get on plane. When she is cold..(not My Wife) the motor, it will take almost 10 to 15 tries before she starts up to even idle....if its not the pump then what is it....... Now i had it in the shop last year because the oil..( Never use pezoil I found out) had fould my plugs. so the mechanic said the carbs looked right and he installed new plugs. But the same problem is present. I had a new lower unit put on last year with the correct gear ratio and prop..but she still does the same thing...so I am not sure what the problem is....
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
Re: 1992 Johnson 200 boggin down problem

Do a compression test first. Then buy an open air gap spark tester and check the spark on all cyls. Should jump 7/16" gap. Then check your timer base linkage to make sure it's advancing properly. Before all this get an OEM service manual if you're going to do the work yourself.
 

CharlieB

Vice Admiral
Joined
Apr 10, 2007
Messages
5,617
Re: 1992 Johnson 200 boggin down problem

When were the carbs cleaned? And a complete 'link-n-Synch' done?

Dirty carbs, mineral accumulation in the idle jets and idle air bleeds will slightly reduce fuel flow making the idle mixture slightly lean. This will cause poor/slow acceleration.

Test this by just 'bumping' the choke/enrichener while accelerating, if acceleration picks up then it is a sure sign that it is time to clean your carbs.
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

Thanks Guys! I talked to a boat mechanic down the road from me and he said the same things you guys are. Check compression. He also mentioned that I should check the spark plugs If they are all dirty or looked like they are being used then it maybe another problem. But he said if you find one that is real clean then its not firing and it maybe the power pack. He also mentioned the timer base, charging coil and the stator. But to do the compression and the spark plug thing first. BTW the carbs were done last year in may. Hopefully I get a good compression check done this next week.
 

SparkieBoat

Captain
Joined
Aug 17, 2009
Messages
3,643
Re: 1992 Johnson 200 boggin down problem

test your fuel pump while you are under the cowl working on it. you need A DVA adapter to test power pack/stator
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

Update. Well finally got to look at the engine. After working nights for a while I got the cover off. I didn't check compression but i did check the spark plugs. I got through 5 of them and all so far looked to being used and thought to myself maybe this wasn't the problem. Got the sixth one out and wouldn't ya know it.... it was clean. So I started at the top left plug and went down and did the same to the other side. The bottom plug on the right side was the one that was clean. Now I have to find out if its the coil assy or the power pack or rec and regulator. If you have any suggestions that would be great!

Thanks!
Razor
 

jonesg

Admiral
Joined
Feb 22, 2008
Messages
7,198
Re: 1992 Johnson 200 boggin down problem

Swap coils and see if the problem follows the coil.
Inspect coil when removed, look on the back and bottom for cracks not normally visible.
If it has cracks its shot.

Get a spark gap tester, they only cost $10 at autozone, set gap to 7/16th inch and test all the coils for strong blue spark.
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

Well took out the coil and it looked fine. Took out the one above it and it looked worse as far as cracks in the rubber but it works fine. Hate to spend the $94 per hour to see whats wrong but it may be better than just shooting in the dark.
 

jonesg

Admiral
Joined
Feb 22, 2008
Messages
7,198
Re: 1992 Johnson 200 boggin down problem

You are being given logical troubleshooting procedures that will isolate the source of the problem.

Did you swap the coils around and see if the problem follows the coil?

If not, then you ARE shooting in the dark.

When you say it sparks fine, is that with the gap tester set to 7/16th inch? a sparkplug is of no use in testing spark quality.
Run your engine after dark and watch the sparks fly from the cracked coil.
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

You are being given logical troubleshooting procedures that will isolate the source of the problem.

Did you swap the coils around and see if the problem follows the coil?

If not, then you ARE shooting in the dark.

When you say it sparks fine, is that with the gap tester set to 7/16th inch? a sparkplug is of no use in testing spark quality.
Run your engine after dark and watch the sparks fly from the cracked coil.

I do appreciate the help. I did not switch out the coils. I did have a friend come check out the coils with his meter and now the bottom two spark plugs have no current going through them. We did get a good spark on the top right but none on the bottom two. The coils checked out fine and he checked out the power pack to and it seemed to work. Not sure what to do next.
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

Well I got the new power pak on and took the boat out this weekend. Boy it took a bit to get her started but she went down the lake pretty well. Just didn't seem as fast as normal. So once we got to our fishing spot we fished for a bit. The went to move spots and wouldnt you know it. It now won't go over 2000 rpms. I am thinking it might have been the gas as it had stabil and a mixture of new gas in it and old gas. Not sure where to go with this now.
 

SparkieBoat

Captain
Joined
Aug 17, 2009
Messages
3,643
Re: 1992 Johnson 200 boggin down problem

re-read post #15..you also need to make sure your motor is not over heating
 

razorsedge31

Cadet
Thread starter
Joined
Jun 18, 2009
Messages
14
Re: 1992 Johnson 200 boggin down problem

re-read post #15..you also need to make sure your motor is not over heating

Well found one problem. The tan wire from the powerpak to the temp sensor was not connected all the way. And according to the directions I found that will keep your engine from running above 2500 rpms. I pulled all of the plugs again and the same one doesnt look like its firing. I followed the manual and tested the coil. Came to 255 ohms. Which according to the book is fine. I did find two coils that I couldn't get a reading on. According to the book those coils need to be replaced. So i am in the process of ordering 2 new coils. I also tested the spark on all cylinders with a screwdriver and got a strong spark. Will get the spark gap tester tomorrow and retest. I also changes two of the fuel lines I replaced last year. I think we cut them a bit short last year and they both looked to be a bit kinked. One last question, can a spark plug be bad and not fire?
 

roofcock

Seaman Apprentice
Joined
Oct 5, 2007
Messages
49
Re: 1992 Johnson 200 boggin down problem

i had a similar issue and it turned out to be dirty grounds at the coils
 

jonesg

Admiral
Joined
Feb 22, 2008
Messages
7,198
Re: 1992 Johnson 200 boggin down problem

Well found one problem. The tan wire from the powerpak to the temp sensor was not connected all the way. And according to the directions I found that will keep your engine from running above 2500 rpms. I pulled all of the plugs again and the same one doesnt look like its firing. I followed the manual and tested the coil. Came to 255 ohms. Which according to the book is fine. I did find two coils that I couldn't get a reading on. According to the book those coils need to be replaced. So i am in the process of ordering 2 new coils. I also tested the spark on all cylinders with a screwdriver and got a strong spark. Will get the spark gap tester tomorrow and retest. I also changes two of the fuel lines I replaced last year. I think we cut them a bit short last year and they both looked to be a bit kinked. One last question, can a spark plug be bad and not fire?

You've had the best advice money could buy already, go back and read through , its all very consistent.
Quit thinking, try following directions when lost. :)
 
Top