1985 Evinrude 20 HP questions

firefightermdo

Cadet
Thread starter
Joined
Oct 6, 2015
Messages
6
I recently purchased a boat that has this motor on it. It is a tiller drive. I noticed when my family and I would go out the motor would run good. However, after we would shut the motor off and try to start it again it would take a lot of pulls to get it started. Anyone know how to fix this? Also I decided to replace the spark plugs, when I put the new ones in I couldn't remember which one went on top. It takes 2 spark plugs. Numbers on the plugs are QL77--- and L77-- I cant remember the last numbers but those are the first few letters and numbers. If yall could tell me which plug in regards to those numbers are on top and which one on bottom that would be greatly appreciated. Thank you very much!
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Both plugs should be the same.------Perhaps previous owner was on a budget.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
They should both be ql77. What is your procedure for starting your motor.
 

firefightermdo

Cadet
Thread starter
Joined
Oct 6, 2015
Messages
6
When I stop the motor I pull the fuel line. Then let it run out of fuel. After I hook the fuel line back up I pump the bulb till tight then I pull the primer. Then pull the cord.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Stop the motor by using the stop button, not by running the fuel out. May be part of your issue....
 

firefightermdo

Cadet
Thread starter
Joined
Oct 6, 2015
Messages
6
alright so I have made sure both plugs are the QL. Now, when I get it started it will run fine. When I slow down from top speed, i notice the motor will begin to bog down and then die. This happened to me twice today. I then noticed a light smoke coming from the two holes in the back, which i am assuming they are the exhaust. I however did not look to see if the water pump was working by looking at the water from the motor shooting out. Also could someone explain to me how the primer knob is supposed to work? Thanks for all yalls help.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
The primer knob is a pump that squirts a bit of fuel into the carb manifold with each pull of the knob on the primer. Should only be used when the motor is cold started and should not be necessary on a warmed up motor. The knob should be pushed in all the way when the motor is in operation. A quick primer or two while the motor is warming up may be necessary.

Is any water coming out the "pisser", the small black fitting on the rear of the belly pan? It will have a hose running to it when viewed with the cowling off.
 

firefightermdo

Cadet
Thread starter
Joined
Oct 6, 2015
Messages
6
Yes water is coming out of the motor. The water pump is working. I noticed yesterday when I drive with the primer knob all the way in it runs great but as soon as I slow down to an idle speed the motor dies. I have to pull the knob out to the keeper ring for it to stay running. Any ideas why or how to fix?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The primer unit is a pump it is not a choke flapper.-----Pull it out and push it in to get the motor started.----Unless you know the age of the waterpump impeller you should install a new one !!
 

firefightermdo

Cadet
Thread starter
Joined
Oct 6, 2015
Messages
6
So I pulled the primer knob off and pulled the stick out. One of the o-rings was broken, so I replaced. I also pulled the carb and cleaned it. However the motor will run fine when full throttle with the primer knob push all the way in, when I slow down, the motor will start bogging down until I pull the primer knob out a little. Any suggestions on how to fix this?
 
Top