1984 Evinrude 15hp E15rcrm

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
have a 15 outboard that i am using at 5500ft elevation. Plugs are wet and slowly getting fouled if i troll a lot. Have rebuilt the carb and set the float to correct level. All ignition components have tested good. Using Xd 100 2 stroke oil at 50:1. Is there a high altitude jet option for this motor. Someone told me the 9.9 jet would work for this but i would lose horsepower
 

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Yes it’s new, tested before installing, verified water is flowing where it should. Thermostat external housing cover heats to about 112 degrees per laser thermometer.
 

Crosbyman

Admiral
Joined
Nov 5, 2006
Messages
6,298
what is a lot ??....2-3 hrs or 20 what if you take an occasionnal run a few minutes to burn of black stuff
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Changing the high speed jet will not change the way it idles !----How are you adjusting the idle mixture needle ?---What plugs are in it.----112 may be too cold for prolonged trolling.
 

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Yes have adjusted idle screw to where motor idles best without cutting out. 112 and it varies up and down a little- is outer cover temp. Internal temp is unmeasurable on my motor. I did test thermostat prior to installing it. It opened in the high 140 degree range, internal temp must be close because thermostat is opening and closing. Standard champion plugs that are recommended for this motor in stalled. Was thinking about gapping plugs to .40 to run them a little hotter.
 

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Plugs slowly start to get a little worse every trip. Motor becomes harder to start and stalls more often. Plugs are visually wet when removed. Lasting about 20 hours before i change them.
 

Rustywrench

Petty Officer 1st Class
Joined
May 10, 2018
Messages
209
You might try the equivalent NGK plug. (Actually just a tad hotter). Some have better luck with them.
 
Last edited:

Rustywrench

Petty Officer 1st Class
Joined
May 10, 2018
Messages
209
You might try the equivalent NGK plug. (Actually just a tad hotter). Some have better luck with them.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Yes have adjusted idle screw to where motor idles best without cutting out. 112 and it varies up and down a little- is outer cover temp. Internal temp is unmeasurable on my motor. I did test thermostat prior to installing it. It opened in the high 140 degree range, internal temp must be close because thermostat is opening and closing. Standard champion plugs that are recommended for this motor in stalled. Was thinking about gapping plugs to .40 to run them a little hotter.

Increasing plug gap won't make them run hotter. But what it will do is force the spark voltage up. That just MIGHT help. Try and see.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Post the results of a compression test.-------Does spark on this motor jump a gap of 7/16" , yes or no ?----Having to change plugs every 20 hrs indicates something is wrong.------Plugs should last 200 hrs or more !
 

CatTwentyTwo

Chief Petty Officer
Joined
Jan 11, 2005
Messages
425
Is the throttle roller set to the cam correctly? The throttle shaft should just begin to move when the mark on the cam is at the center of the roller.
 

Attachments

  • photo290714.jpg
    photo290714.jpg
    475.8 KB · Views: 0

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Compression 105 and 110. Cam roller set for correct timing per manual. Have to test spark jump for 7/16.
 

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Ok it jumps 7/16 spark gap. Trying the new plugs today with .40 gap to see how it runs. Will keep post updated
 

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Ok runs fine. New plus gapped to .40 Plugs are still getting wet though. Have only run it at idle with muffs on at home. I’m gonna take it out fishing tommorow and see how it does.
 

stink bait

Cadet
Thread starter
Joined
Aug 15, 2012
Messages
10
Heres a pic of plugs after 5 hour fishing trip today l. combination of wot and trolling. motor ran great, both plugs were new prior to trip and dry afterward.
 

Attachments

  • photo291331.jpg
    photo291331.jpg
    285.6 KB · Views: 0
  • photo291332.jpg
    photo291332.jpg
    323.8 KB · Views: 0
  • photo291333.jpg
    photo291333.jpg
    338.4 KB · Views: 0
Top