1983 Johnson 70HP J70ELCTE Slows down a LOT with Load

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
Water can clean a plug. Did you check for spark? It's the next step.

Yess i just did. 7/16 gap. I do have sparks. Tried taking a video but phone camera wont capture the fast sparks.. But yess sparks are there
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
No Title

No good. You don't just want to use "what was in there before", use the OEM recommended plug.
Might be the same, but make sure.

Just picked up oem recomend sparkplugs from oreally. .. Champion L77JC4 Marine... Do gap have to be adjusted on new plugs???? I measure it and is bit over .025... And i read here it works bettar on .030 or .040
 

Attachments

  • photo245585.jpeg
    photo245585.jpeg
    226.2 KB · Views: 0

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Sounds like the bottom plug has no spark when it's under compression. If it has no spark, that means whatever fuel gets into the bottom cyl, it won't combust since there is no spark. So, could be raw fuel. If it's water, it turns a milky/white color when mixed with fuel/oil.
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
Sounds like the bottom plug has no spark when it's under compression. If it has no spark, that means whatever fuel gets into the bottom cyl, it won't combust since there is no spark. So, could be raw fuel. If it's water, it turns a milky/white color when mixed with fuel/oil.

Okay then it maybe fuel cuz its clear... Not milky... However i swap plugs and wires between cylinder and still same.. Why wouldn't the plug get sparks??
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You have tested that spark will jump 7/16" in air at atmospheric pressure.--That means it will easily jump that gap when in the cylinder and the air in the gap is at 140 PSI or 10 times the pressure !
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
No Title

Why is the bottom cylinder runing on lower RPMs?

I attached two tachometers one to bottom cylinder and one to middle cylinder:
https://youtu.be/j5wv8TlmWQ0

One to Bottom and to Top Cylinder:
https://youtu.be/e9d3QtMdenk

And then bottom and top at Highr RPM while in neutral gear:
https://youtu.be/uUqQs4Gs-BU

Middle and top stays arround same 1,400RPMs
And bottom cylinder at 700s RPM. About half less.
This also hapen with the wire conected to open air gap tool instead....
Right after taking the videos took out plugs, and bottom was very clean, again.

So i dont understand why the bottom wire is running at lower rpms. I thought they all 3 suppost to be the same rpm??
Is this normal on this engines???? :/
 

Attachments

  • photo245599.jpeg
    photo245599.jpeg
    111.2 KB · Views: 0
  • photo245600.jpeg
    photo245600.jpeg
    164 KB · Views: 0

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
If you don't have a factory oem manual go to cdi electronics and use their ignition trouble shooting guide. You will need an ohmmeter, a DVA Adaptor or peak reading voltmeter and the ability to follow step by step directions without skipping or cheating. i would bet money it's the power pack though it could be sensor coils or a broken flywheel magnet
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
I watched the third test you posted in #52 post. I really can't see how one of the tachs reads 4400. I'd say the 2200 reading tach is reading correctly. I'd agree with jaked-you should generate voltage output readings for your stator and for the timer base. You may have a weak ignition component. Keep in mind that weak components tend to work well when they are cold. Once the engine heats up to normal operating temps, a weak component can start to fail.
 
Last edited:

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Are you still running that supressor cable on the bottom? (See post 3.) If so, try moving that cable to another cylinder and see if the problem follows.
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
Are you still running that supressor cable on the bottom? (See post 3.) If so, try moving that cable to another cylinder and see if the problem follows.

Nope i picked a oem cable yesterday. And then i also swap cables arround with no effect on anything
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
I watched the third test you posted in #52 post. I really can't see how one of the tachs reads 4400. I'd say the 2200 reading tach is reading correctly. I'd agree with jaked-you should generate voltage output readings for your stator and for the timer base. You may have a weak ignition component. Keep in mind that weak components tend to work well when they are cold. Once the engine heats up to normal operating temps, a weak component can start to fail.

The third video is throttle advanced in neutral gear. I advanced to 4,400s rpm on top and middle cylinder. Dont matter what rpm they running, bottom cylinder is always runing about half less on rpm, in this case 2,100s..

So like you and jake said there IS a ignition problem.
I have the manuals I bought as a PDF.
This:
https://drive.google.com/open?id=0B3dyjVyh6WiXa0tqalhWMkhpclU

And this:
https://drive.google.com/open?id=0B3dyjVyh6WiXWjNNd2ZmRnhHaVE


I Will read on the ignition section and see how to test that powerpack
 

WernerF

Petty Officer 1st Class
Joined
Sep 5, 2011
Messages
320
The third video is throttle advanced in neutral gear. I advanced to 4,400s rpm on top and middle cylinder. Dont matter what rpm they running, bottom cylinder is always runing about half less on rpm, in this case 2,100s....

The motor wasn't spinning 4,400 rpm. Much slower. You can hear it.

Hook up a timing light on every cylinder and watch for irregularities/differences of the flashes.

The #3 spark plug has never seen fuel or a combustion.
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
The motor wasn't spinning 4,400 rpm. Much slower. You can hear it.

Hook up a timing light on every cylinder and watch for irregularities/differences of the flashes.

The #3 spark plug has never seen fuel or a combustion.

I think it never seen combustion. Because there will be raw fuel when removing the plug
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
No Title

Guys i forgat to mention something, the reason i replaced the bottom sparkplug Wire is cuz it was very rusty on the boot that conects to ignition coil... And the ingnition coil conection had rust on it too. So i kinda sand it to remove rust and make good contact with new wire boot... Does that rust rise any flag??

Piics attached
 

Attachments

  • photo245628.jpeg
    photo245628.jpeg
    120.6 KB · Views: 0
  • photo245629.jpeg
    photo245629.jpeg
    164.2 KB · Views: 0

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Was it a factory spark plug wire? They are special wires. When it comes to diagnosing ignition problems, I prefer using the CDI troubleshooting guide. Many of the early factory manuals only have your check for ohms readings. Later factory manuals (and all the CDI manuals) provide both ohms and crank voltage ouputs. Check this website out: cdielectronics.com. They have excellent condemning values from cranking voltage outputs on the componets of your engine: stator, timer base. Once you know those outputs, you also can then check the voltage outputs from the spark plug end of the coil connector. (that tests the power pack.)
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Spark can jump a gap of 7/16" ----a little rust on that spring will not be a problem.
 

osito2789

Cadet
Thread starter
Joined
Jun 3, 2016
Messages
20
So i tested the powerpack output voltage. And i don't understand why im getting low readings.. I followed manual instructions, unplugged the 4 pins conector between powerpack and ignition coils.

Jumpwire the 3 pins(A,B&C)... Conect the black multimiter lead to ground(any bare bolt) and red lead to metal part of the jumper lead A on the powerpack conector... And i gues the fourth pin (the black one) on conector leave it without jumper lead..
Reading between 9volts and 13 volts... Same with B and C.. How??? I doubt engine could run with such a small voltage from powerpack. Im doing something wrong??

And if i plug the multimiter black lead straight to the fourth pin (instead of engine ground) it will be worst, like 1 to 2 volts...?
I used a 12gaug wire as jumper but i don't think that woild have any impact.. Even when i plug the multimiter red lead straight into the powerpack conector cavity still had same volstages...

Plus i couldn't turn off engine during testing, i had to unplug sparks plugs wire so engine dieds.(is this normal)?

Voltages did go up to like 20s and 30s when i rev up engine. But thats it...

Service manual calls for at least 230V..
 
Last edited:
Top