1980 johnson stinger randomly doesn't start

mdf806

Recruit
Thread starter
Joined
Jun 30, 2016
Messages
5
I've owned this 1980 Johnson motor for 10 years. Its a 3 cylinder 75hp Stinger. I've never had major issues with it. Last year it left me stranded in the middle of the lake on 2 occasions. This year its done it once so far. The engine runs great and always starts right up when leaving the dock for the first time of the day. I can go out all day and fish starting and turning the motor off many times. Sometimes I have no problems restarting the motor. Other times it will just randomly not start. When it doesn't start i can pull out each plug one at a time and all plugs are sparking. I'm getting fuel to the cylinders cause the plugs are wet with fuel. I've pulled off all three carbs and cleaned them. I've replaced the plugs with new ones. I've rebuilt the fuel pump. I've replaced the fuel ball handpump and all the fuel lines leading from the tank to the motor as well as all the fuel lines on the motor running to the carbs and such. Compression in the cylinders is within 8 psi. I'm leaning towards weak spark even though i have spark but im just guessing on that. I'm stumped on this. Anyone have any advice? Everytime i get towed back to the dock i can go down the next day and the damn motor will start right up no problem. The motor runs great at low speeds and WOT. I just cant trust it anymore to start up once out on the lake. Like i said its very random. I've probably started the motor up 40 times or more so far this year and it hasn't started just the one time that in had to be towed in. I'm sure it will happen again though as it did twice last year. I dont get it.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
Next time it won't start do an open air gap spark test set to 7/16"

Requires a tool. Holding plug to block and looking for spark tells you absolutely nothing useful.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Let's see: choke plate has to work -- fully open and fully closed (make no assumptions). Old ignition parts can start to fail when hot. Unfortunately, you often have to diagnose sporadic problems when they happen. Test spark with the tester just to see what you have, but carry the tester with you out on the lake so you can check for spark when the motor is acting up (like Jakedaawg suggests). Doesn't have to overheat to generate ignition failures, but want to be sure the engine is running at proper temps -- never over 160F. Top of the head shouldn't be too hot to touch. Operating tell-tale is good, but not fully conclusive. If overheating, it may not restart until cooled down. Finally, want to be sure it's cranking over well -- strong battery and starter, connections clean and bright.
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
Difficult warm starts aren't that uncommon, we just had another long thread on the same subject. It's normally just like what you said, run it for a while, shut it off for a period of time, then 1 out of 10 times it won't start for no apparent reason.

After the above mentioned things, try holding the key in and squeezing the primer bulb a couple of times, this doesn't work for every motor, but it will on many.

http://forums.iboats.com/forum/engi...93-johnson-70hp-2stroke-won-t-start-when-warm
 
Last edited:

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Whenever it randomly won't start, you may be having ignition issues. Common when you have a weak ignition component, like a timer base, power pack or stator. Weak ignition components run fine when cold. Once the engine warms up to normal operating temps, the weak component tends to break down and you get no fire. Left overnight, the engine may start right back up and run fine for a while-then start crapping out again. So, when it won't start-do a couple of ignition tests: 1. check to see if the spark will jump 7/16" on a spark checker. 2. Check each plugwire with a timing light to check for spark. 3. If it will run (poorly) do a cyl drop test to see if one (or more) wire(s) is dead.
 

mdf806

Recruit
Thread starter
Joined
Jun 30, 2016
Messages
5
Thanks for all the input. I will grab a spark tester to see if I can get an arc at a 7/16" gap. To answer some of the other responses......The water pump (impeller) is brand new as i just replaced it this spring. The water coming out of the motor now is barely warm. Before i replaced this the water coming out was hot and the stream didn't come out with as much pressure. Choke plates are working when the key is pushed in as you can hear and visibly see them close when the airbox is removed. Lastly I replaced the battery last year and I cleaned all my connections already as i though that may be the culprit. I may just pick up a powerpack online and throw it on, they are only about 100 bucks online. So for now i'll just wait for it to not start and then run the spark test. I'll let you guys know how i make out. Thanks for the help.
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
So yours does have a choke, not a primer system? I wasn't sure which year they made the switch.
 

mdf806

Recruit
Thread starter
Joined
Jun 30, 2016
Messages
5
yes it has electric choke. you push the key in on the ignition key and a solenoid on the motor engages the choke on all three cylinders. So you can start the engine with or without using the choke by either pushing in the key or not pushing the key inward while turning it.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Different answer to a different question.... With the good old choke plates, electric or not, the plates have to fully close and fully open on cue. Hearing the click may not be good enough -- same with seeing the plates move from a distance. For choking, the plate has to shut tight or you will get poor starting. Best approach is to touch and feel the plate closed tight. Lube the shaft and linkages, and make sure the electric diaphragm and wiring is up to the job.
 

mdf806

Recruit
Thread starter
Joined
Jun 30, 2016
Messages
5
Ok I will double check that the plates are fully closing. i'll let you know how I make out. Thanks for the insight.
 

mdf806

Recruit
Thread starter
Joined
Jun 30, 2016
Messages
5
i just bought a new power pack and a rectifier online. I figure the motor being as old as it is it cant hurt to replace these in hopes of curing the problem. I got both for about 100 bucks so to me its worth it. When i get them next week after the holiday i will post any new news. My plan this weekend is to check the spark with tester and verify the choke plates are fully closing.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Interesting. Even if the pack and rectifier turn out to be surplus right now, not bad to have on hand for future testing and use. Trick is to somehow insure the new parts are good. If your fix turns out to be something unrelatated, think I would be tempted to work in the pack and the rectifier, one at a time, and see if they are good, then keep for future reference.
 
Top