1979 140 evinrdue high idle

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
Engine ran and idled but cut out around 1500 rpm in the water. Left bank wouldn't fire 7/16 gap. Replaced stator. Trigger, both power packs and 3 ignition coils. Broke one of them so one is still original but works fine. Is just saturated and leaking. Have not set high speed timing yet but at idle with timer base all the way back runs about 2k rpm. Stator, power packs were replaced at earlier time and idled great. Seems to be after replacing timer base. Any ideas would be greatly appreciated.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Did you torque the flywheel properly? If not, the key can shear and change the timing. You can test by pulling #1 plug and running the piston to top then confirm the pointer is at the TDC mark.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Is the throttle linkage actually against the idle stop? Are the carbs for some reason not fully closed?
 

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
Yes, I backed the stop off the throttle linkages and never came down. If you open the throttle about manually it will rev up. Almost as if the timing is already being advanced. I will have to check the keyway.
 

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
The flywheel key is sheared. I did not have to correct tools with me at the time when installing the flywheel. Will have to fix that. Thanks for the input!
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
You need to use an OEM key, not something you find at Home Depot. Did the crank nose keyway get burred?

You need to deburr the tapers on the crank and flywheel, and lap them before re-assembly with valve lapping compound using the flywheel on the crank with no key. After that, you must clean the tapers completely with brake clean or similar non-residue cleaner. The tapers need to have intimate contact, and the correct torque in order to properly seat and hold.
 

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
Will do, thanks for the info. Also does anyone know about what degrees the timing should be at in gear idle?
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
There is no timing spec at idle. Retarding the timing is how the idle speed is adjusted.
 

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
Got it running and put in the water today. Runs pretty good at idle. Once you go past 3/4 throttle it will bog down and it will never get over 2k rpm. It will run at 1/4 throttle for a few mins around 15-1800 rpm but will eventually bog down. If wot quick it will die as if it's running lean but don't really see anything wrong with it. Took the top carb apart just to look and was clean. Checked the fuel pump screen and diaphragm. Didn't visually see a problem there either. Adjusted wot timing to 24. Any suggestions would be appreciated.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Read your spark plugs? And try pumping your fuel primer bulb when it's acting up.

And how did you set WOT timing if it won't run there? Did you use the Joe Reeves method?
 

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
What do you mean by read the plugs? The timing is advanced all the way around half throttle or something around that and it will run for a min and I set it while running down the water so it wasn't actually wot but timing was advanced all the way. Also I have tried pumping bulb and also tried spraying with ether but didn't seem to have any effect. I'm not sure what Joe reeves method is. Thanks for the quick responses. Also i am staying by the lake so I can't put it in water quick
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
What dies a compression test show on this motor ?-----Post the numbers.
 

Austindh

Cadet
Thread starter
Joined
Sep 12, 2016
Messages
9
My compression gauge is at the shop it will be 12 days before I could do that. I haven't taken compression test. I took two short videos around 1 min I was trying to post.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Trouble shooting will get you results.----You appear to be struggling with this motor.----I would do no more spending $ or effort till I did a compression test !!
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
By reading the plugs, I meant pull them and see if they all look the same. Since you have no access to a compression gauge you'll have to wait to do that test.

But if it 'peters out' after running a while, that really sounds like you're starving for fuel. To confirm or dismiss fuel starvation, pumping the primer ball when it's acting up will fill the carbs. If it runs better when you pump the ball, your problem could be a bad fuel pump, air leaks in the supply line, or poor crank case compression, even bad reeds.

You can do a crude test for reeds by seeing if you get excess fuel spitting out the front of the carbs when it's idling with the intake cover off. Hold a business card an inch or so from each throat and check for spray colleting on its surface. A fine mist is OK.
 
Top