1978 Johnson 9.9 RPM issue

Carte238

Recruit
Thread starter
Joined
Jun 6, 2016
Messages
3
Hello all, new member here trying to get to the bottom of an issue I'm having with my 1978 Johnson 9.9 (10R78W) that I have installed a new 15 hp carb in approximately 1 year ago. The motor is on a 12 foot plastic bass boat, and I have had no issues with it since I purchased it 2 years ago, other than installing a new fuel pump last season. Up until 3 trips ago, the motor ran like a top. By myself (170 lbs) with gear it ran anywhere from 18-23 mph, 2 people with gear 13-15 mph. It got onto plane great, even with 2 people. Recently the motor has been acting odd. In the morning as soon as I hit the lake, it runs like normal. Gets on plane, ran at 15 mph today with 2 people and gear.

Ran down the lake, fished off the trolling motor for a couple hours, then went to run back up the lake, and the motor suddenly begins to act terribly. 7 mph with 2 people, will not get on plane. At WOT the motor does not sound like it is revving near as high as earlier in the day. This has happened on the past 3 trips out now. I run premium pump gas, mix at 50:1 and run ethanol treatment in the tank. I just replaced the plugs with NGK BUHW-2, old plugs were black tipped, but not terrible.

Ran new gas today without ethanol treatment, still having the issue. It's the oddest thing, it runs perfect when I hit the lake, but begins acting up when I go to run somewhere else after fishing. I have read all kinds of posts and forums, but I have no idea where to start. Any help would be appreciated, thank you.
 

OptsyEagle

Lieutenant
Joined
Sep 13, 2006
Messages
1,367
The first thing I would do is put in the proper spark plugs. Your motor specifies Champion QL77JC4. Even when I cross reference them with NGK I don't come up with the plugs you are using. With NGK, usually there is a number somewhere that you have a "U" that specifies a heat range.

Sounds like you are probably running on one cylinder. Why that happens can be many things but a spark plug fouling is certainly one of the culprits. Use a plug a couple heat ranges colder then specified and you will be lucky to get a couple of hours out of the spark plugs before they fail.

Anyway, put in the proper spark plugs and try it again. If by some chance I am right, then think about doing a decarb in the near future. If improperly burned carbon was getting all over those spark plugs, you can be sure it was also crudding up your cylinders and piston rings.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Use a timing light on the plugs and see which cylinder is loosing spark.--------Is the thermostat installed and working properly ?-------Check the pins and sockets on the rubber electrical plugs.
 

Carte238

Recruit
Thread starter
Joined
Jun 6, 2016
Messages
3
Just put the proper plugs in and purchased some seafoam. Going out tomorrow, will see if this fixes the issue and let you all know!
 

OptsyEagle

Lieutenant
Joined
Sep 13, 2006
Messages
1,367
OK. Great. The seafoam never hurts. If I were you I would put in the proper spark plugs and take it out and see how she works. If everything is now OK, do the seafoam treatment and enjoy the motor.

Right now, it does sound like you may be running on only one cylinder but I am really just shooting in the dark that it is being caused by the wrong plugs. If you put in those correct plugs and you are still having a problem at the top end then I would do a cylinder drop test, just to confirm or rule out the bad cylinder theory.

A cylinder drop test is fairly easy. Your motor should run very well on only one cylinder, except it will suffer for power at the top end of the throttle range. So to confirm if both cylinders are working, start up your motor and let it warm up. Bring it to a FAST idle and with a pair of insulated pliers, pull one spark plug boot at a time. If the motor dies when either of the boots are pulled off a spark plug, you now know that the other cylinder was never firing or is very weak.

With that information we should be able to help you identify the cause of it, if it turns out not to be a fouled spark plug.
 

Carte238

Recruit
Thread starter
Joined
Jun 6, 2016
Messages
3
Update: The motor ran better today with Champ plugs. Instead of losing power after the first run, it would lose power for a few minutes, then regain power an get to proper mph. I pulled the top boot while idling in fast, and the motor shuddered and died.
 

OptsyEagle

Lieutenant
Joined
Sep 13, 2006
Messages
1,367
Sounds like the bottom cylinder may be failing intermittently. I assume it ran OK when you pulled the bottom plug boot?

At this point I would want to know what compression you have in each cylinder and if the ignition can produce a spark across a 3/8" gap using an external spark tester.

I would look at both of those spark plugs and see if there is a noticeable difference. Is the bottom cylinder all wet with black oil over the electrode or is it shinny clean or does it just look like the other cylinder's plug?

Another quick test you can do is switch the spark plug boots and the coil clips to the alternate cylinders. After the switch, run the cylinder drop test again and see if the problem jumps to the top cylinder or stays with the bottom. If the problem moves to the top cylinder, after the switch, you have just isolated it to that secondary coil. Either a bad coil itself or a bad plug wire, etc. If it stays with the bottom cylinder it can be quite a few things like a bad powerpack, or a problem with the compression of that cylinder, bad head gasket and perhaps a few other things.

Anyway, those are my thoughts.
 
Top