1978 johnson 70 hp ignition issues

tjohnson110772

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
10
Hey i have a 1978 johnson 70 hp that i cant seem to get the ignition to work.I got a new ignition switch,battery and solonoid.I got it hooked up and at first the electric choke would engage and when i pushed the nuetral safety switch i heard something from that to,but now i have nothing...any ideas?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Explain what you mean by " pushed the nuetral safety switch " --------And it sounds you need to review how you hooked it all up.------Me thinks the fuse is now blown.
 

TrollPro

Cadet
Joined
Jun 13, 2013
Messages
14
need more info, is the starter solenoid engaging or making any noise?

I have essentially the same motor and have been going through my ignition issues, just got it back and purring again, hope we can help you out as I feel like a dang expert (almost) now.
 

tjohnson110772

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
10
to trollpro..the solonoid is making no noise at all.this thing is abasket case..lol..the previous owner hacked up alot of the wires and im trying to figure them out.when i first hooke up the battery the electric choke was engageing but now i got nothing.is there suppose to be a fuse somewere?ive checked my wires to new ignition switch a cuople of times and seems to be what im seeing on diagram
 

tjohnson110772

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
10
to racerone....not sure were the fuse is on this thing...but i had the control box open when i did the ignition switch so i pushed the safety switch in to see if it worked,thats when the electric choke stop working
 

tjohnson110772

Cadet
Thread starter
Joined
Apr 9, 2016
Messages
10
the only switch i have is a toggle for i belive is for the bilge pump then two pull out switches for lights..thats it..old boat
 

woodstockmarine

Seaman Apprentice
Joined
May 6, 2012
Messages
37
I had the same problem and one of the levers that move when you open the trottle was sticky and was not coming back all the way and wasn't hitting the neutral safety switch on the engine block. I forced the lever back by hand and moved it back so it was depressing the switch and it cranked over.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Do you have the factory manual for your motor if not get it and if you do you will have to check each wire separately. There is nothing worse than a hacked up wiring harness. The wires are color coded so should not be to bad.Once the wires are correct you can start trouble shooting the right way. The fuse is on the motor by the big red plug.
 
Last edited:

TrollPro

Cadet
Joined
Jun 13, 2013
Messages
14
yes should definitely have one to prevent blowing out the other ignition components when there is a spike in draw.

as for the kill switch I am referring to the dead mans switch, there is a lanyard that is attached to a little plastic clip that slides on the dead mans switch on the controls. if this is bad, it is assuming that the switch has been pulled and will not allow the motor to start.

Check it with a multimeter between the two wires, if you have continuity, replace, or fix the switch, if it doesn't then its working as it should. Again, assuming you have the plastic clip attached properly. zbvzbz
 

AlTn

Commander
Joined
Mar 9, 2010
Messages
2,813
at the very beginning of the Forum.. highlighted in yellow...is the Closed Sticky File : Top Secret Files...look here and the 2nd. file reads ..Johnson/Evinrude Wiring Diagrams...the 1978 70 hp. is included...this may be a benefit to you
 
Top