1978 Evinrude 115 Running on 3 cylinders

tbach12

Recruit
Thread starter
Joined
Jun 14, 2017
Messages
5
I have a 1978 Evinrude 115 that is running great on three cylinders but the lower cylinder on the port side is not firing. I cleaned the carbs and checked the spark. The fuel seems to be flowing evenly through both carbs. There is plenty of spark on all 4 spark plugs but one cylinder will not fire. I am going to check the compression today after work but are there any other problems that would cause one of my cylinders not to fire besides low compression?
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
If you have spark on all four but you suspect one isn't firing, how are you determining that? Did you do a cylinder drop test?

Have you tested compression?
 

tbach12

Recruit
Thread starter
Joined
Jun 14, 2017
Messages
5
When I pull the spark plug wires, that cylinder has no change. The other three will almost cut the motor out when i pull them. I have not done a compression check yet. I will this afternoon.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
When I had one coil fail and the engine was running on 3 cylinders, I would not have said it was "running great". Rather it was shaking and bogging and weak. I thought it was on 2 cylinders, but it was just one bad coil. '82/78 140hp mashup motor. Problem with the coil cropped up when it was still a 90 and then happened during trials on the 140 build.

Another good test is to clip a timing light on each lead and run the motor at speed on the lake - look at the light pulses and see if there are dark spots happening randomly.

When you pull the plugs, post a pic of all 4 tips.
 

tbach12

Recruit
Thread starter
Joined
Jun 14, 2017
Messages
5
Update: I tested the compression. The cylinder in question, bottom left, has 85psi. The top left and bottom right also have 85psi. But for some reason, the top right has 40 psi. I rechecked the spark on all of the plugs and they are letting off a nice white spark. When i pull the wire off of the plugs, they all change the pitch of the motor and even cut it out except the bottom left. That one does nothing when i pull it. When i give it gas, it sprays a nice mist out of each carb. Does not seem to be a problem there. I did a visual check of the head gaskets and it does not look like there is any blow by. So first, how do I get the bottom left cylinder to fire, and second, how do I fix the compression on the upper right? (it wont let me add pictures)
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Time to remove cylinder heads ! --------Sounds like the classic failure.----------Broken piston rings.
 

tbach12

Recruit
Thread starter
Joined
Jun 14, 2017
Messages
5
Do i have to replace all or just the one with low compression?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Some will argue.-----If you do one you will likely do this job again next year.---But take the heads of first for inspection.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
Yup. Heads off. You can inspect the rings by turning the motor until each piston is at top then move it around and look into the gap with a flashlight. Broken rings usually end up pounding a bunch of dings in the piston crown and cylinder head.

In this shot, the head at left shows dings, the one on the right is OK. Note the head gasket on the right is blown between the two cylinders.

IMG_0449_zpswznit0wg.jpg


Piston dings:

IMG_0457_zps9wlitmv0.jpg


Here's a scored bore and a ding where the broken ring hit the port:

2fc12ed1-8cb2-4a2d-b120-bdb8b684767a_zpstz9uha08.jpg
 

tbach12

Recruit
Thread starter
Joined
Jun 14, 2017
Messages
5
You guys were exactly right on the one that had low compression. I took the head off and it looks similar to the pictures above. It does not have any "ring strike" like the one above and the side walls are not chewed up at all. I think i am just going to order a new piston and rings and put them in. Or is it a necessity to have it bored out? On the cylinder that would not fire, the head gasket was blown at the bottom and i believe it was pouring in some water. Thank you for the help and the pictures.
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
At a bare minimum, you need to hone the bores and install new rings. Something to consider: pistons with years on them will have loose ring grooves that will allow the rings to move around too much, chancing another failure in short order. You also risk losing the indexing pin which keeps the ring from rotating and having a ring end catch a port.

If you're going to the trouble of opening it up, four pistons, rings and a master gasket kit are in order. And get a factory service manual for your year to ensure you have the right procedures and specs for assembly.

Before spending this money, you also need to decide if it's worth the dollars/time, especially if you're paying for labour.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
1) Get a manual 2) Get new pistons/rebuild kit 3) Bore it .020 over 4) Use it with no worries
 
Top