1977 evinrude starter issues!!!!

dwalters219

Cadet
Thread starter
Joined
Feb 6, 2017
Messages
13
I got a 1977 evinrude 25hp (25752s) from a guy and the starter was locked up it And the carb needed rebuilt but hey it was FREE so I have hardly nothing in it... I rebuilt the carb and had the starter rebuilt and it has new coils I hooked it all up and when I tried to turn it over the starter would engage but it would hardly turn the fly wheel around like it is in a bind it will make one roatation and then almost lock up but barely move then it will make another rotation I not to familiar with boat motors but I was just going to see if there was anything I could try it was free and I don't have $100 in it and it's really good shape please help!!!
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Will the engine turn nice and easy with sparkplugs out ?-------Will the starter crank it over properly / fast with plugs out ?-----------Oil in the gearcase checked ?----What other trouble shooting was done on it ?
 

dwalters219

Cadet
Thread starter
Joined
Feb 6, 2017
Messages
13
Haven't tried it with the plugs out the only things I have done is what I posted like I said I'm not no boat mechanic but as soon I can check it I will I was told to take the fly wheel off and make sure their ain't no gunk built up up under it
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I guess everyone has their own approach.---good luck with it.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Might do this. With motor on a test stand, remove the lower unit.

Pull out the plugs. Turn the flywheel clockwise by hand -- should feel a compression bump, but should otherwise turn freely and smoothly. Should be no grinding or metal on metal noise. If moving freely, spin with the starter (plugs still out). If hesitation like you describe, your battery isn't charged or is too weak for use, or you have poor connections. Sand and polish all connections until shiny and try again. If still no success, have the battery load tested or try another one. If you finally get the motor to spin normally/rapidly with plugs out, do a compression test -- cylinders should be close to equal. Do a spark test using an adjustable tester to see if the ignition needs work (should see about a half inch spark if the ignition is good).

Turn to the lower unit. Drain the gear oil and check condition (milky means water, and needs to be corrected). Assuming oil is clear, refill the gearcase and replace the impeller. Reattach to engine and crank the engine in the lake (preferable) or in a barrel -- make sure it's pumping water out of the exhaust opening on the back of the leg. If so, clean, regap and replace plugs. Then move to trying to start and operate the motor -- revisit ignition issues if appropriate, and test with fresh gas and 2-cyle oil (50:1 mix).
 

dwalters219

Cadet
Thread starter
Joined
Feb 6, 2017
Messages
13
I got the plugs out and it's turns over perfect no grinding or nothing going to drop the lower unit tomorrow but just a thought i had earlier if it's not spinning like it needs to with both plugs in it could the exhaust tube be plugged on it and not letting it vent right?
 

wrench 3

Commander
Joined
Aug 12, 2012
Messages
2,108
If it cranks OK with the spark plugs out and the starter is rebuilt, it's probably not getting enough juice to the starter.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
There is something wrong with the starter / battery / battery cables.
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
Yeah. check those cables - use a wire brush and polish ALL the connectors shiny clean. Apply some dielectric grease. If the cables are badly corroded, they should be replaced.
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
Crab the cables when you're trying to crank it and see if they're getting warm.
 

dwalters219

Cadet
Thread starter
Joined
Feb 6, 2017
Messages
13
Ok guys I wire brushed all the connections as good as I possibly could got it all back together and it's still doing it I took the starter back to the guy who rebuilt it and he went through it again and aid nothing was wrong with it and tested it thoroughly I have a brand new optima blue top on this thing so I dunno what else to do with it... I'm getting a compression gauge this afternoon from a friend of mine I know they say motors vary with compression they just need to be close but what is a tolerable distance as far as psi between the two cylinders? And what would it be for a 25 hp as far as compression needed?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I am saying there is a problem with the starter / battery / battery cables.------Use a set of booster cables and go direct from a good battery to the starter motor.
 

lmuss53

Lieutenant Junior Grade
Joined
Sep 9, 2008
Messages
1,227
I agree with racerone, take a known good freshly charged battery and jump directly to the starter with known good cables, I bet it cranks like it should.

I have a 25 Johnson here right now that did this because of a corroded factory installed terminal on the ground cable. The cable looks fine but won't carry enough current to crank the motor, I found the issue by jumping a good battery right to the starter with my good jumper cables. Once I knew the starter was OK I chased down the bad cable using the jumper as a ground wire and finding that the ground wire was bad.

If you are doing that (known good battery, and cables, directly to the starter) and getting slow cranking I would start to suspect the rebuilt starter.
 
Top