1977 Evinrude 70 stalling under load

petersbc

Seaman Apprentice
Thread starter
Joined
May 19, 2013
Messages
38
This is a bizarre problem. Had the boat out on the lake for "sea trials" today. We had an issue with it staying running in reverse but it was ok in forward for a while. Once we got out past the no wake zone I was able to bring the engine speed up to 3800 RPMS and get 17 MPH out of the boat. That seemed to be pretty typical for a 24 foot pontoon boat sporting a 70. The problem came when we shut the motor down at the back of the lake for just a few minutes. It was hard to start and once started I could not give it any throttle in gear or it would die. We finally found a throttle position where it would stay running, at the "start" marking on the throttle lever, but only at 1200. Any more throttle and it would die. After heading back at 3MPH for 30 minutes we started messing around and found a very slight amount of choke (we had the cover off and applied it by hand) and the engine would pick up some and I could throttle up and run back at 3800. I experimented with it as this condition would make it very hard to recover the boat and found anytime coming off of idle when it wanted to die I tapped the choke switch (push in and release the key quickly) 3 times and the motor would pick up and run.

Another issue is when starting the engine and using the "cold idle up" lever, or what ever you call that throttle lever, it would take quite a while for the engine to build speed. My assumption was at no load the throttle response should be very quick.

This is a new to me 1977 Evinrude 70HP
New fuel pump
New fuel lines
Rebuilt carbs
new plugs
Compression 125 or better on all three
All three plugs were firing at idle but I have not checked it today.
New water pump
new Gear oil (not that that matters but....)

This is on a 24 foot pontoon boat that I've just finished rebuilding from the pontoons up. Today was the first day out on the lake.

When I first brought it home the motor ran really badly on the stand but after I replaced and rebuilt everything listed above it would start easily and seemed to free rev well. This work was done last November and the motor has been sitting on a stand in the garage until last week. I did not "winterize" it so the fuel that was in the bowls did evaporate but that happens all the time here in AZ and it's never caused me issues with four stroke motors of all kinds.

Sorry for the book but it's a crazy problem.
 

bplayer405

Cadet
Joined
May 3, 2013
Messages
29
Re: 1977 Evinrude 70 stalling under load

Your idle mixture screws are set too lean. I had the same dilemma on a mariner 48. The carbs have to be set with the engine in the water. Setting them out of the water removes the added backpressure of having the exhaust under water. Believe me it makes a big difference! Start by turning out the mixture screws half a turn each and see if that helps. They need to be set with a warm engine in forward on or off the trailer in water.
 

petersbc

Seaman Apprentice
Thread starter
Joined
May 19, 2013
Messages
38
Re: 1977 Evinrude 70 stalling under load

Rebuilt the carbs which is just a cleaning on this motor and had the boat out yesterday. That solved this problem and the new 15P four blade prop worked much better. Got 18 MPH but only 4400 RPM but figured that was due to the extra 500 pounds of people food and beer I was carrying.

The latest problem is a cylinder cutting out. When I hit some chop the motor will fall off and only give me 3K then another bounce and it's back to full power. Seems like an ignition problem but that is another thread.
 

phillnjack2

Ensign
Joined
Apr 30, 2011
Messages
918
Re: 1977 Evinrude 70 stalling under load

you need to get that engine to 5000 -5000 revs, so i would be looking at a smaller prop for a start.
youl probably end up with a 13 pitch prop to get the right rev range.

anything lower than 4800 revs at full throttle and your gonna be choking the engine up and get bad fuel economy and
dirty oiled up plugs.
wuith a smaller pitch youl also get a smoother pull away and just better running engine all round.

15 pitch prop is good for water ski-ing on a 15ft speedboat, on a 24ft pontoon its too big.

also how far under water is the cavitation plate when the boat is on the plane ? it realy needs to be just on or slightly above the
water when the boat is on the plane.
too much under will cause too much drag and act like the engine is too small and under powered !!!!!!!!!!!

also like you say,there is a loose ignition wire somewhere that needs to be found or a bad earth !!!


phill.........
 

petersbc

Seaman Apprentice
Thread starter
Joined
May 19, 2013
Messages
38
Re: 1977 Evinrude 70 stalling under load

According to the Clymer manual this motor should run at 4600-5000. You said 5000-5000 I assume you meant 5500 which, by the book, is too much for this motor. Also this is a typical 80's pontoon boat, it does not plane. The motor is as high as it can be installed and is still a bit low for my liking but it can not go any higher.

Fuel economy is not a concern but longevity is so you may very well be right about needing a 13 pitch. I have another prop to try that is an 11 pitch and we'll be back on the lake this weekend with the same load so we'll see if it is too small. I'm quite sure if it had only been the two of us on the 15P I would have been in the power band but I guess I need to size the prop for the typical load. Thankfully the props I'm looking at are cheap.
 
Top