1976 stator test

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
I have a 1976 115 HP Johnson testing stator (no spark issue) it's the 4wire 2 yellow 2 brown. Yellow wires Ohms are 1.3 .brown wire from power pack 0 ohms to ground. I am sure there should be .500 or so through brown wires to ground. No reading signifies an open circut ?
I think. I am assuming the stator on this engine grounds through mounting bolts. Since there is no separate ground wire as I have seen on other stators. Bad stator ? Rectifier seems to check out ok with ohms test.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Doesn't look like anyone's going to jump in here so I'll take a shot at it.

Use Low Ohm Scale

Timer-base sensors -- Between the two wires of either sensor = 8.5 ohms +/- 2.0 ohms

Between the brown/yellow & brown wire of the stator = 630 ohms +/- 75 ohms

Between the yellow wires of a 6 amp stator = 1.2 ohms +/- .2 ohms...... a 12 amp stator = 0.5 ohms +/- .2 ohms

If you have PTT, the stator is most likely a 12 amp model.

Any of these wires to ground = ZERO! ... any reading indicates a short.

(Small Rectifier Test)
(J. Reeves)

Remove the rectifier wires from the terminal block. Using a ohm meter, connect the black lead of the ohm meter to the rectifier base (ground), then one by one, connect the red lead of the ohm meter to the yellow, yellow/gray, then the red wire (some rectifiers may also have a fourth yellow/blue wire. If so connect to that also). Now, reverse the ohm meter leads and check those same wires again. You should get a reading in one direction, and none at all in the other direction.

Now, connect the black lead of the ohm meter to the red wire. One by one, connect the red lead of the ohm meter to the yellow, yellow/gray, and if present, the yellow/blue wire. Then reverse the leads, checking the wires again. Once more, you should get a reading in one direction and none in the other.

Note that the reading obtained from the red rectifier wire will be lower then what is obtained from the other wires.

Any deviation from the "Reading", "No Reading" as above indicates a faulty rectifier. Note that a rectifier will not tolerate reverse polarity. Simply touching the battery with the cables in the reverse order or hooking up a battery charger backwards will blow the diodes in the rectifier assy immediately.
 

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
Thanks Joe

I will double check the ohms on the brown wires from stator to power pack. I only checked them to ground I think. It has been a long day. The rectifier turned out okay. But for $18.00 I might change it out anyhow. I am testing coild as well. Using a meter that has ohms as 20 , 200 , 20k,200k and 2000k setting. Using the 20 on the ohms reading for the stator and get 1.3 on the yellows. Back to the garage and I will check the brown again. Funny thing is this engine test fired about a month ago. I changed the lower end and now no spark. Not a single component of the lower end has anything to do with the ignition. Rather than the Nuetral switch. No shift interrupt switch or lanyard on this oldie. Thanks for the reply. I will get back on the brown/yellow and brown ohms...
 

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
so OHMS meter set at 2000 I get 682 ohms on brown and brown/yellow wire. zero to ground. So this means stator is good. Correct ? Yellow wires set at 200 have 1.3 ohms. I was thinking the engine was not getting to 300 + rpm on crank but it is. Timer base wires. 12.9 ohms... Starting to think the power pack is fried....
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
Remove black/yellow wire from ignition switch or powerpack. If you have spark with that wire disconnected BUT no spark with it connected, replace the ignition switch. All s/plugs must be removed during the spark test.
 

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
Thanks.. I will see if that works tonight... It would be great to have just a bad ignition switch...
 

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
Going to recheck everything and start from beginning. Removed black and yellow wire from power pack and no spark. Double checking all component tonight and tomorrow night..I will get back to you. Appreciate your time Sir. If it were an I/Ov6 or v 8. Even a 4 or 6 banger. I would have it figured out by now
 

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
Removed Rectifier and found no Ohms through red and yellow/gray and ohms only through red and yellow. No ohms through case on Red and or yellow /gray. Only yellow. Reversed Meter leads and same. so rectifier turns out bad after all. One on order and then we will see what happens. seems the stator and the timer check out okay.
 

Matster

Cadet
Thread starter
Joined
Jul 1, 2018
Messages
7
Hey Joe..... Rectifier got it running.... Had Ebay bucks and it cost me $3.98..... Thanks for all your help and appreciate your time. Now on to the cables and adjusting the shift rod after replacing the lower end. Thanks again sir. Happy Boating...
 
Top