1975 Evinrude 40 hp

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
Good Morning all, new to this forum. Just bought a boat about a month ago, and when my wife and I took it out for the first time it ran ok. But it would get up on plane. Almost seemed as if it wouldn't top out on RPM. But would surge aswell. Now it dropped a cylinder completely. According to the spark plugs the bottom cylinder is running correctly (has that nice golden brown color) but the top plug is very sooty and black. But wet also. Both cylinders seem to have good spark in open air. I am at a loss. Thank you to anyone that could help me figure this out!
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
I originally figured that's what it was so I put a new one in that cylinder and immediately with the same result.
 

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
You have what is called low tension magneto and was used shortly during the 70s.They tend to foul plugs, well at least mine does. I have a 1976 40hp with the same ignition system. It is possible that you might have better luck with NJK B7HS plugs. Also your points need to be clean and gaped correctly, but if you say you have spark then concentrate on the plugs or the boots.
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
Ok, I will go try that right now! Thank you very much for the info and I will get back to you on it!!
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
ok, so heres what I did. New NGK plugs, number as given, installed fired up runs the same. While running pulled top plug wire, very lil change but a slight change. Could also here arcing. Put wire back on and pulled bottom cylinder wire, instant stall. Did it a second time with the same result. Inspected both plugs and top plug is clean but drenched wet, while bottom plug is dry but lil dirty.
 

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
Sounds like you have no spark on the top cylinder. Check to make sure the plug lead is screwed in the coil correctly. Maybe unscrew it and clip a little bit off and also check the plug end inside the boot. If problem persists swap the coils and see if one is bad. And then if it is not the coil then it is time to remove the flywheel and inspect, clean and gap the points.
 
Last edited:

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Check the fuel pump diaphragm too.
racerone beat me to it. That's what I was about to say. Is the fuel pump on the top cylinder that is flooding? If it is, remove it (leaving fuel lines attached) and give the primer bulb a squeeze. If gas squirts out the backside of the pump, that is the problem.
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
The top cylinder is definitely flooding. I swapped the coils and I get the same result. So I definitely have good spark in both cylinders. But the top cylinder must be dumping so much fuel it cant burn it. I thought there was only one pump but I will go check right now. Thank you all! I will keep updated.
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
There is only one fuel pump and all is good with that. Took it off and squeezed the bulb as instructed and all good. Diaphram is in good shape. I'm at a loss lol.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
As you are hearing some arcing somewhere, should run that down -- start it up after dark and see if you can see it -- could be one of the boots or cracked wire insulation.
 

hardwater fisherman

Lieutenant Commander
Joined
Mar 19, 2010
Messages
1,725
As you are hearing some arcing somewhere, should run that down -- start it up after dark and see if you can see it -- could be one of the boots or cracked wire insulation.

I think what he meant is when pulling the plug wire off he heard arcing.
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
Put one of those fancy spark testers on there and there is good strong spark in both cylinders. I even swapped coils around and got the same result. Both cylinders tested out to have 120 psi compression. And no spark leak. Could it be a carb issue?
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
Have great spark. Even swapped coils around to verify. Both cylinders have 120 psi compression so that's good. Definitely seeming like a fuel issue at this point. And with one carb and one pump on two cylinders I am not sure where to start. Would a carb rebuild solve the issue potentially?
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
NOT the carburetor. It feeds both cylinders. But there is a slight chance it could be the reeds. Rare but possible. Could also be getting water into the non-firing cylinder. Did you see any on the plugs when you pulled them?
 

mayns22

Cadet
Thread starter
Joined
Aug 5, 2016
Messages
19
Have not noticed any water no. But you can literally dump the gas out of the spark plug in the top cylinder and it runs.
 
Top