1974 9.9 Johnson

shh...buzzards

Recruit
Thread starter
Joined
Apr 29, 2017
Messages
2
I just purchased a1974 9.9 Johnson motor. Evetthing seems to work fine in the test barrel, when I put in on my 14' Jon ithas no power beyond idle speed. It shifts into both gears easily and revs with throttle twist, but no thrust. The motor will idle along fine, but then when I give to throttle it is like spinning your wheels on an icy street. The engine revs and things seem to be spinning under water, but the boat stops moving.
I am new at working on my own motors.
Any help will be appriciared.
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
You can check for a spun hub by marking the end of the prop shaft ( or just use the head of the prop nut cotter pin as reference) and mark the prop in line.

Go for a spin on the water.

If the marks no longer line up it proves its a spun hub
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
The description shouts out loud and clear: Spun prop hub. If it isn't that, then drive shaft splines. You don't want to even think about that.
 

77kingfisher

Seaman
Joined
Apr 24, 2017
Messages
71
If its not your prop hub its most likely your clutch dog and gears ware they contact together. If its not your hub the easy way to confirm the gears is take the lower unit apart and inspect both gears and clutch if any of there contact surfaces are rounded at all :apologetic:. If they are one of 2 things need to happen replace ($300 and up) or mill them not at 90*s!! Mill them at some ware between 3-5*s off from 90*s so your digging into the base and working into the top. I have 2 outboards that I got cheep for this reason both came with "spare" props :lol:. One is an 18hp 1970 evenrude the other is a 1971 40hp Johnson. Took a stroll down to the neighbors and used the mill and 45 min later presto. Reassembled tested in the lake and whoop works perfect :D.
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
If its not your prop hub its most likely your clutch dog and gears ware they contact together. If its not your hub the easy way to confirm the gears is take the lower unit apart and inspect both gears and clutch if any of there contact surfaces are rounded at all :apologetic:. If they are one of 2 things need to happen replace ($300 and up) or mill them not at 90*s!! Mill them at some ware between 3-5*s off from 90*s so your digging into the base and working into the top. I have 2 outboards that I got cheep for this reason both came with "spare" props :lol:. One is an 18hp 1970 evenrude the other is a 1971 40hp Johnson. Took a stroll down to the neighbors and used the mill and 45 min later presto. Reassembled tested in the lake and whoop works perfect :D.
If it was a worn clutch dog it would tend the throw itself out of gear, having to be re-engaged with the shifter to restore drive.

A spun hub would simply drive again when throttled down and slip when throttled up
 

77kingfisher

Seaman
Joined
Apr 24, 2017
Messages
71
If it was a worn clutch dog it would tend the throw itself out of gear, having to be re-engaged with the shifter to restore drive.

A spun hub would simply drive again when throttled down and slip when throttled up

True unless it is truly round and at idle is "OK" and then under throttle skips every time. As in my case and having just purchased the motor its a question I ask. Most people would ask enough people to find out its a prop hub and fix it. So is it the "expensive side of things"? That's all im saying.
 
Top