1974 165 hp tilt/trim wont lower

chris812

Cadet
Thread starter
Joined
Feb 5, 2011
Messages
24
Hello, I was wondering if somebody could help me with an issue I am having with my trim/tilt? I recently bought a boat from someone (Mercruiser) and apparently I am having some issues with the trim/tilt not lowering. I replaced the pump with a good used one which was tested and still the thing wont lower. I called the people I bought it from and they said that there is probably air trapped in the pump and I needed to partially unscrew the screw to the low pressure side to release the air. have not tried that yet. the cylinders do have new seals in them so they function smoothly. the unit does move up fine and the motor runs in the down . when I do push the in the trim indicator does move. could there be a problem with the reverse lock? I have a manual but it does not tell me much for troubleshooting all of it. All I am looking for is all possible scenarios. Any help would be great.
 
Last edited:

Bob_VT

Moderator & Unofficial iBoats Historian
Staff member
Joined
May 19, 2001
Messages
26,121
Re: 1974 165 hp tilt/trim wont lower

Sounds like there is an airlock. Sometimes you have to loosen line fittings and physically move the drive up and down. This will normally clear the airlock.
 

chris812

Cadet
Thread starter
Joined
Feb 5, 2011
Messages
24
Re: 1974 165 hp tilt/trim wont lower

Well that was not it either. Called the guys back and they thought I was referring to a different pump. Anyway they tell me that the pump is self bleeding. so now they are telling me it could be the reverse lock control. I am really at a loss here. according to my manual for the troubleshooting it says "Unit fails to release from full up position"
1. internal resistance in either one or both cylinders.
2. fluid level low.
3. pump pressure low or no pressure.
The next one relating to that is "Unit fails to return to full down position or fails to move smoothly(moves with jerks)"
1. hoses reversed on one cylinder.
2. air trapped in the system.
3. pressure low or no pressure
4. internal resistance in one or both cylinders.

Now I checked to be sure hoses were in correct position on cylinders, I replaced the seals in both cylinders but I did not bleed according to manual. so could air in the cylinders be the culprit or is there possibly something else? Remember this is a working pump. Any info would be great I really want to get this in the water soon.
 

Bob_VT

Moderator & Unofficial iBoats Historian
Staff member
Joined
May 19, 2001
Messages
26,121
Re: 1974 165 hp tilt/trim wont lower

My method was to bleed out the air trapped first. That is a "no cost" repair and the best place to start.......
 
Last edited:

RRitt

Captain
Joined
Mar 30, 2006
Messages
3,319
Re: 1974 165 hp tilt/trim wont lower

air will cause a system not to raise. It does not affect lowering.

As you extend the pistons fluid is withdrawn from reservoir.
At some point the pump runs out of oil and the system stops raising.
As you lower fluid is pushed back into the reservoir. The system refills itself.
 

chris812

Cadet
Thread starter
Joined
Feb 5, 2011
Messages
24
1974 165 hp mercruiser tilt/trim problem

1974 165 hp mercruiser tilt/trim problem

Hi, I posted on trim tilt not lowering and did some extensive tests on everything. High pressure and low are within specs. Tested direct from pump. Bled all the air out and still not lowering. I noticed that when I had the up line disconnected from the gimbal housing and still attached to the cylinder and the down line connected to both cylinder and gimbal. I ran the down circuit and oil came out the up line but cylinder did not retract. I don't believe it is suppose to do that right? So can someone please tell me what's wrong here.
Also all three holes were plugged in gimbal except down port.
Thanks
 
Last edited:

Bondo

Moderator
Staff member
Joined
Apr 17, 2002
Messages
71,545
Re: 1974 165 hp tilt/trim wont lower

Ayuh,.... Keep postin' in the same thread, so yer Info stays together, Ok,..?? Thank you,....

With both lines disconnected, does the drive lift, 'n fall easily,..??
 
Last edited:

achris

More fish than mountain goat
Joined
May 19, 2004
Messages
27,468
Re: 1974 165 hp tilt/trim wont lower

There could be a few issues. The most common is that the end cap in one of the rams has corroded and is 'grabbing' the piston rod. UP pressure (3000psi) is sufficient to overcome the resistance, but down pressure (1700psi and working on less than half the surface area of the piston) is not. Another possibility is that the bolt securing the ram to the piston has come out. The piston may be moving, but the piston rod is not.

HTH,

Chris....
 
Top