1973 65hp Johnson electrical issue

uscgcolletti

Cadet
Thread starter
Joined
Mar 16, 2017
Messages
7
Ok I was running my engine after changing som fuel lines.... running fine. I secured it to place the cover on and then it wouldnt start. After some trouble shooting I realized the solenoid wasn't closing so I got a new one. Now its closing and I'm getting power to my starter but my starter isn't doing anything. I got a new starter and bench tested it and it works off of a spare battery. However when I place it back on the motor when I turn my switch I hear a "zip" electric sound and nothing. Starter won't click... just nothing. if I remove the battery cable.. the solenoid closes and again I verified power is getting to the starter. Any thoughts?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
sounds like your spare battery is the one to use. Need to sandpaper all the wire connections until shiny.

afraid I don't understand what you mean here: "if I remove the battery cable.. the solenoid closes and again I verified power is getting to the starter."
 

uscgcolletti

Cadet
Thread starter
Joined
Mar 16, 2017
Messages
7
I have a full load on my battery and i used a load tester. the battery in the boat is fine. When I say I removed the battery cable I mean the cable from the solenoid to the starter. When thats removed the soleniod closes and opens everytime I turn the key. However when I put that cable back on the starter.... nothing. And if I'm click too many times I burn out my solenoid
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Clean and inspect your battery cables and connections. They aren't allowing enough current to pass through to the starter.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Are you sure it burned up? Could have been the other problem and you were just experiencing the symptoms, not the actual problem.
 

uscgcolletti

Cadet
Thread starter
Joined
Mar 16, 2017
Messages
7
No, the other soleniod burnt up. I put 12vdc from my spare battery and its not changing state.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Whatever you say.
But I've often said I'm going to buy some stock in the solenoid factory. The majority of "bad" solenoids are not bad at all. People run out and buy a new one and it doesn't fix the problem. But of course, there is the occasional bad one.
 

uscgcolletti

Cadet
Thread starter
Joined
Mar 16, 2017
Messages
7
well how would you test a solenoid? The main contacts should be normally open, when 12VDC is applied to the control side the main contact should close allowing voltage to flow. If the main contact isn't closing thats a bad solenoid. Unless I missing something
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
If it's an outboard solenoid, and attached to the engine, the starter should spin if you jump one of the small solenoids to positive and the other small solenoid to negative (jump from the battery).

You may have a fuse between the S post of your starter switch and the big post of the solenoid (battery side, not the starter side). I think a third positive wire from that post might go to your rectifier, but not sure. Look for a blown fuse interrupting keyswitch operation.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
I'm not there to see exactly what you did, just taking your word for it. What might you be missing? Well the safety switch for one thing. And of course the cables that we've been preaching about. Bottom line is I don't know if you have a bad solenoid or not. Just wondering....
 

uscgcolletti

Cadet
Thread starter
Joined
Mar 16, 2017
Messages
7
I appreciate all the help, however i took the solenoid off the motor. Applied 12vdc to the small contacts. Its not changing state..Hence why I got a new one and that one is changing state. It eben changes stat while attached to the motor. The issue Im havign is when I connect the main contacts from the soleniod to the starter it doesn't nothng
 

uscgcolletti

Cadet
Thread starter
Joined
Mar 16, 2017
Messages
7
Well the simple things... I took a dremel to most of my connections. Cleaned them up nice final got it started. I will be on the water tomorrow. Thanks for the assistance
 
Top