1972 Johnson 40 Electric Start NO SPARK

bmanis

Recruit
Thread starter
Joined
Apr 30, 2018
Messages
4
Greetings All. I've enjoyed reading these forums for the last couple of years. I picked up two 1972 outboards with an old boat a couple weeks ago. Both have set in a barn for a dozen years. One is a 6hp Evinrude Fisherman that I was able to get running well. The other one is giving me some problems.

It's a 1972 40hp Electric start. I've cleaned up all the terminals and wiring contacts and the electrical system appears to be fine; relative to what I've read on these forums. The engine is cranking great and compression is very good, but I'm not getting any spark.

Any ideas?

Help is greatly appreciated!
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Assuming it is wired correctly, and the key is turned on, it is time to pull the flywheel and see what's wrong in there. You need a puller to get the flywheel off and you MUST use a torque wrench to tighten the nut to 100-105 foot pounds when reinstalling it.
 

bmanis

Recruit
Thread starter
Joined
Apr 30, 2018
Messages
4
Thanks for the quick response. At the moment I have the safety switch removed as it was rather "sticky" but I'm getting the same result. Could that be the culprit? Also, the two black magneto wires are reading continuity. Should they? I thought the purpose of those wires was to "kill" the engine when they contact as the switch is turned to off.
 

bmanis

Recruit
Thread starter
Joined
Apr 30, 2018
Messages
4
To verify, the wires I am reading continuity on are the two black wires coming from under the flywheel. I tested for resistance after disconnecting from the vacuum cutout switch and the single wire harness. I'm reading continuity even with the key turned to on. I took a pic but the file is too large to post.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Not a valid test. The wires go to the points, one of which is always closed (grounded). Not only that, the wires go to the leads to the primary windings of the two coils. The other end of the primary winding is grounded. So a continuity test would actually be showing the resistance of the primary winding, which is only about an Ohm.

The vacuum cut-out switch doesn't do a darn thing unless the engine is in runaway condition. Otherwise, a honking big spring inside the switch is holding it open. It takes a high vacuum to overpower the spring and close the contacts.
 

bmanis

Recruit
Thread starter
Joined
Apr 30, 2018
Messages
4
Gotcha. That makes sense. I'll pull the flywheel next then. How does the safety switch work? I find it odd that it only has one wire coming to one side of the switch, and nothing on the other side. I guess I just don't understand it's operation or it's purpose. Thanks again.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
In a barn find, more likely coils -- and may be apparent when the flywheel is removed. If the housings are cracked, they need to be replaced. (In that situation, it's not a bad idea to just replace points and condensers as well.) Good find, btw.

The ground lead from the cut out switch has an insulating washer, so is grounded only if the switch closes — thereby grounding ignition. The switches can fail closed, but not really the place to start. Start with the assumption you will need to rebuild the magneto, and work from there.

May be preaching to the choir, but measure both compression and spark with appropriate testers. For a spark tester, check an auto parts store for the adjustable open-air variety — not the inline style. Like checking compression, test with both plugs removed .
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Vacuum cut-out switch: Probably beating this to death, but in response to your question, here's what it is all about. If the engine revs up beyond a critical point in neutral (or if you lose a prop, etc), it will run away--that is you cannot slow it down. The purpose of the vacuum switch is to sense that runaway condition and cut the ignition to one spark plug till it slows down. Once the RPM is under control again, the vacuum switch opens and does nothing until next time.

If you look at the vacuum switch, you will notice is is mounted on a plastic plate. That means it is not electrically grounded. Enter another switch--the starter safety switch operating off the magneto plate/throttle spark advance. The starter safety switch grounds the vacuum switch body, but only at slow throttle settings. That is to prevent false vacuum cutouts at certain high throttle settings (boat up on plane and going fast in cruise throttle setting).

SO, if a high vacuum occurs at slow throttle settings (runaway) the vacuum switch closes, connecting one set of points to the switch body. Still it isn't doing anything yet because the switch body isn't grounded (the plastic mounting plate). Now IF the starter safety switch is closed (slow throttle settings), then the vacuum switch body is grounded and can do it's job of killing the one cylinder till RPM is under control.

The only way the vacuum switch can fail in a closed position is if the spring inside is broken or rusted away. Possible, but so rare you would have a better chance of winning the lottery.

Hope this isn't too deep for anybody. It is complex but actually simple.

Now pull that flywheel and see what's wrong with your ignition system.
 
Top