1972 Johnson 25hp starting problems

Laszlo462

Recruit
Thread starter
Joined
Apr 25, 2017
Messages
5
Hi all,

Last year we obtained a boat from a family friend with a '72 25hp outboard. Ran fine the couple times we had it out. Previous owner took good care of it, and the couple times we had it out it started after 1 or 2 pulls. At one point late summer, I ran into an issue where I couldn't start it for the life of me. Was still at the launch so I fished from shore a bit and took it back home. After alot of trying and testing spark, I finally did get it started. When it was time to winterize it was hard to start but got it running and winterized.

So far this spring, I cannot get it to fire more than a second on the first attempt. Taking the plugs out, they're wet, so I let things dry a bit and try again. Same issue (starts to fire then dies, then nothing on subsequent pulls). I've since replaced the plugs, replaced the fuel pump, checked the flywheel key, things look great under the flywheel, carb torn down and rebuilt multiple time (clean as a whistle), and checked compression. Compression is at about 70psi on both cylinders.

I've run out of ideas, and can't get more than a quick second of firing before she dies right away and won't so much as pop again until the plugs are dried.

Going to try new fuel this week, since I've got spark, fuel, and compression. Any other ideas I'm missing?
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Are you mixing the gas and oil? Get a different compression gauge and re-do the compression test because those #s are low. How are you testing the spark? Is it with an open air spark tester.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Agree with flyingscott. In addition, cleaning and resetting points might be key. Assume when you say everything looked OK, the coils didn't show cracking (a sign they should be replaced) -- can be tested to be sure, but points are probably the most likely culprit. The carb idle needle may need some additional tweaking -- potentially a little leaner, if your plugs are getting soaked. A 50:1 fuel ratio should be fine on that motor.
 

Laszlo462

Recruit
Thread starter
Joined
Apr 25, 2017
Messages
5
Thanks guys. Spark test was the old school "ground out the plug" way, couldn't find a tester with adjustable gap locally. I'll have to grab one off amazon. Regarding under the flywheel, I was surprised at how....new everything looked for lack of better words. Coils looked good, but I should get back under there and check the points one more time. I didn't have a guage to measure the gap, but they both looked good from an initial check. I did notice, one of the rockers for the points has a little bit of up and down play in it. So I'll have to take a longer look at those, haven't really dealt with that stuff since high school, so hopefully some stuff I learned comes back to me (I'm only 32). Last night was more of a cursory check to make sure there wasn't something blatant like a blown coil under there.

Thanks again guys, I'll keep plugging away at it, I appreciate the help you all give here.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You pull the choke lever out.------------But have you actually looked to see if the shutter is fully closed and stays closed after pulling it over ?
 

Laszlo462

Recruit
Thread starter
Joined
Apr 25, 2017
Messages
5
Well I can rule out gas and/or vaccum lock of the fuel tank. Same issue, first pull ran for for about 2 seconds. So I'm back under the flywheel, thinking I'll probably end up replacing the points after I get an open air spark tester. At this point, it's gotta be that the spark isn't strong enough.

One question I have regarding the older Johnson outboards and the points; as the crankshaft turns and opens each set of points, there is a period of time when both points are closed before the next one opens. Is this normal, or should the next set of points be opening pretty immediately after the first set closes? Although, as long as they're gapped appropriately, I'm assuming timing-wise they should be opening/closing at the correct times.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
When the rub arm is at the high point of the cam, set the gap at .020. Set the flywheel back on, and rotate a half turn clockwise. Lift the flywheel back off. The rub arm for the second set of points should now be at the cam high point -- set that gap to .020. That should do it for you. Make sure the contact surfaces are clean (business card and a little acetone works well). Put the flywheel back on without tightening it down. Using the adjustable spark tester, give the flywheel a couple of sharp flips clockwise, checking both leads for spark. If spark measures somewhere close to a half inch (say, 3/8 inch), torque the flywheel down.

If a set of points is not down tight on the post, as you seem to suggest, it's probably because the little wire clip is missing. Unfortunately, you need the clip -- may need to buy a set of points to get one. (Maybe somebody has a fix.)

Choke flap has to close and hold tight for starting, as racerone suggested. Similarly, when you push the knob back in, you need to be sure the flap is fully open (rich running if the flap remains partially closed). It's a hands-on (or fingers-on) exercise to make sure it's right.

And if you see cracks in a coil wrap, replace the coil. Actually, it usually makes sense to just replace them both at that point.

Finally, your carb idle adjustment needle needs to be set correctly. Initial setting is 1 to 1 1/2 out to get the motor to run, then dial it in from there. (warmed up, in gear, lower unit in the lake or deep in a test barrel).
 

Laszlo462

Recruit
Thread starter
Joined
Apr 25, 2017
Messages
5
Thanks Oldboat1. Finally got around to testing spark with an adjustable tester. Spark won't jump anything close to a half inch, only much smaller, with one lead jumping better than the other. So, on to replacing the points/condensers. Thanks again all for your help.
 
Top