1972 50hp Evinrude(electrict shift)question.

seeplakermaverick

Recruit
Thread starter
Joined
May 30, 2018
Messages
3
Is there any way to crank this motor over to check compression? I have the control box but it has been gutted. No push buttons, no ignition or choke switch. I have the wire harness and throttle cable.

Also, what power head is compatible with a 1978 55hp Evinrude ( different year or hp) ? Thanks for any input.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You can use booster cables straight to the starter.-----Best find a used control box.----You need a control with the big ---YELLOW -----Plug on the harness.----Not red , not black.----Yellow and there are not many around.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
1. Disconnect the yellow wires from the rectifier
2. Remove spark plugs and ground both plug wires
3. Use jumper cables to crank the motor. Attach red cable to starter terminal and battery (+). Connect black cable to battery (-). Touch other end of black cable to a solid ground on the motor. Do not make and break the connection to the starter terminal as the arcing can cause severe damage to the terminal.
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
But with no power to the shift forward gear will be engaged so prop will spin ???

If so care needed ( or remove prop )
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
But with no power to the shift forward gear will be engaged so prop will spin ???

If so care needed ( or remove prop )

Good point, that thing can slice meat if you get into it.
 

seeplakermaverick

Recruit
Thread starter
Joined
May 30, 2018
Messages
3
Well, I found a parts motor for it, with control box(100% complete) with yellow plug. I got to looking inside the control box real good and noticed there are no wires connected to the forward push button, is this normal? Also, a gray wire has been cut, not sure what the gray wire goes to. Any help would be great. Thanks.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Not a pro here, so not sure about the gray wire, but yeah..
I'd expect no wires on the FWD button..

There's 2 types of electric shift I know of anyway...
Hydro-Electric: the green wire is for Neutral and Blue is for reverse.. Apply 12V to green for neutral and apply 12V to BOTH green and Blue for reverse.. No power to either is FWD, so the FWD button really just releases the other 2 (if one is pressed) so they aren't closed either..

Straight Electric: apply 12V to green for Neutral and 12V to Blue for reverse.NOT power to both...
But still, FWD would release the other 2(if one is pressed) as well... No power to either would be FWD...


It's one of the above 2, and I THINK yours is Hydro-Electric. I have a 71 Johnson 50 and it's a Hydro..
These pro's could confirm that for you though as I very well could be wrong as to which electric shift you have... .

Hope it helps!
 

seeplakermaverick

Recruit
Thread starter
Joined
May 30, 2018
Messages
3
Ok thanks. One motor is a 1971 and the other is a 1972. Both are 50hp Evinrudes. Yeah, I'm pretty sure both are hydro. The forward push button does have 2 metal terminals coming down from it but no wires connected to it like the neutral and reverse buttons do. I only paid $100 for both motors, control box(yellow plug wire harness). I figured between the 2, I could make one of the motors run real good. Both motors are 100% complete. Same with the control box.
 

55Crestliner

Petty Officer 2nd Class
Joined
Aug 31, 2004
Messages
192
The FWD terminals will have 2 wires attached. On my setup, they are both white. One white wire goes to the "S" on the ignition switch, and one goes into the wire harness coming from the motor.
This setup prevents the motor from even turning over if the FWD button is pressed.

Just an FYI, unrelated, but in case you or anyone else ever runs into this issue, I discovered that if the throttle is up too high, this motor will not start. No turn over, nothing. Not really sure HOW I diagnosed this one, but glad I did. Was really racking my brain, and it nixed a nice Sunday morning cruise on the last day of a resort stay a couple weeks ago.
 

todd281

Petty Officer 2nd Class
Joined
Jan 21, 2015
Messages
159
Just so you know, there were some changes made in the lower gearcase units between 1971 and 1972. they are interchangable with the powerhead, but some of the internal parts are not.[different driveshafts and lower housing]. Keep in mind that that motor , with no power to the shifting wires is defaulted to forward. power is supplied only to shift to neutral or reverse.
 
Top