1971 Johnson 125 questions

regulars

Cadet
Thread starter
Joined
Feb 14, 2011
Messages
10
Ok some background. Im not a outboard mech at all. However I build and tune motors all of the time. Last motor I built, dynoed and tuned peaked at 800hp. So I understand power drops, fuels systems etc. When you say that the Johnson has 80-95hp at the prop is that peak HP? What does the entire run look like in TQ and HP is it a flat run holding consistent TQ and HP? Or does it spike and then drop off? How about the Mariner is that peak HP and what does the run look like through the rpm range? If they both peak at the same HP but the Johnson due to larger displacement holds TQ and HP at higher or even levels through the entire rpm range and the Mariner is lower through the RPM range then to me it would be worth using the Johnson. Idont care about Peak HP, I care more about what power it holds through the entire rpm range. As far as the fuel pump being 110gph, that is just a volume measurement. Ill look and see if it has some sort of pressure regulator and see what pressure it holds. Im just looking for the best bang for the buck here. Its a fish and ski boat. So if this Johnson holds HP and TQ through the range it will pull people much better with less power loss.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Both motors reach max torque and Hp at 5000rpm due to design porting(forget 4 stroke theory), Running it over set rpm may gain 2-3 hp but the engine has reached its max volume in/ exhaust out and then the curve will start to drop..To get torque figure take hp x 5252 and divide by RPM so the 125 @ 5000 RPM makes 131 ft.lbs torque at powerhead. The 90 is 121 ft.lbs at powerhead but a shorter stroke and 2 extra cylinder which make curve rise faster.. The 90 will pull skiers and tubes better as it 99ci also..
 

regulars

Cadet
Thread starter
Joined
Feb 14, 2011
Messages
10
Both motors reach max torque and Hp at 5000rpm due to design porting(forget 4 stroke theory), Running it over set rpm may gain 2-3 hp but the engine has reached its max volume in/ exhaust out and then the curve will start to drop..To get torque figure take hp x 5252 and divide by RPM so the 125 @ 5000 RPM makes 131 ft.lbs torque at powerhead. The 90 is 121 ft.lbs at powerhead but a shorter stroke and 2 extra cylinder which make curve rise faster.. The 90 will pull skiers and tubes better as it 99ci also..
What do you mean by 2 extra cylinder? I thought the 90 is a 3 cylinder and the 125 is a 4 cylinder.
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
What year is the 90 as it came 3 ways...Inline 6, 3cyl small bore and 3 cyl big bore. I assumed you had the I6 motor....
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
1987 was the first year of the 3 cylinder 90hp. 71.1 cu inch block WOT rpm range 4750 - 5250. gear ratio 2.3:1. Oil premixing system. Power trim. I am assuming it is not an Optimax. Later years may have also had a 90 hp designed for pontoon boats, with a larger displacement and propeller
 
Last edited:

regulars

Cadet
Thread starter
Joined
Feb 14, 2011
Messages
10
So after the new findings that the 90 is a 3 cylinder and it is a 1987, the 1971 125 seem to be the better choice over the 90?
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
The 125 V4 will be more powerful from the 40% increase in displacement over the 90. The 90 will have much better fuel economy over the 125 due to it being, 3 cylinders, loop charged, and 16 yrs of fuel efficiency improvements. Parts should be easier to find for the 90 being newer. The 125 has the Hydro-Electric shift, and while it does shift smoothly and quickly, it is getting harder to find parts and people who UNDERSTAND how it works and how to fix it when malfunctions. The 90 has an oil mixing system, with the 125 you are the mixing system. Some people love the Oiling system, others don't trust it.
 
Last edited:

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
I'll still put my money on 99 crossflow cubes having more low end than 71 looper cubes. 40% more displacement
 

interalian

Commander
Joined
Jul 23, 2009
Messages
2,105
My crossflow feels like it wants to tear out the transom when I hit it. Get prop blowout too - do I need a cupped prop? Way too much fun.
 
Top