1964 40hp Big Twin, problems, fixes, more problems, more... eh.. fixes?

Drummermike58

Cadet
Thread starter
Joined
May 27, 2018
Messages
6
Model number: 40452 S

So I recently acquired a 1965 Sears/Elgin fiberglass runabout in somewhat restored condition. It had been sitting for a couple years so I wanted to get it running to take my dad out for the weekend on it's maiden (to me) voyage. I started by sorting cleanup, and identification of missing parts. Ended up buying a new 6 gal fuel tank, replacing the fuel fitting on the outboard side of the primary line, getting a new deep cycle marine battery, and general cobweb removal. It came out pretty well up to this point.

First attempt in getting it running (by the way I have NO IDEA WHAT I AM DOING, though I am mechanically inclined and versed in auto mechanics) I had gotten a few attempts at turning over the motor in a barrel of water. It would't seem to catch, engage the choke at the push button, or show signs of life. On out final attempt, zero movement or click at ignition. I assumed bad starter solenoid, so with 5 minutes to close 9:55pm I made to the auto parts store and secured a solenoid for a 70's ford maverick that looked the part. install and continued troubleshooting failed oil 12am, when I decided to go to bed. Woke up at 7am and made it back to the auto parts store and bough a new ignition cylinder. as this was the morning of the "maiden voyage" I took my chances, loaded the trailer, and headed down to my folks place. Upon arrival I knew we had work to do...

I started by replacing the ignition cylinder which did nothing, then with a multimeter my dad's buddy happened to have, found (after much delay and work) a poor connection at the fuse panel. Turns out corrosion ACTUALLY DOES prevent good continuity. After removing the fuse panel, and scouring it with a wire brush to good clean metal, we were in business observing 12v everywhere it was supposed to go. I replaced the original (marine) ignition cylinder (turns out it's frowned upon to use auto ignition cylinders) I started to figure out how it was wired improperly. After coming to the conclusion that the "M"'s on the cylinder are for magneto, and act as a spark arrester when n the off position, followed by properly wiring the electronic push button choke, we were making progress. After finalizing wiring, we were able to get the motor to turn again! Sweet, back to 12 hours ago where I was. Now to find out why it wouldn't fire...

We observed fuel leaking from the throttle body when priming, so I knew fuel was at least getting TO the carb. I decided to pull the carb and see what was happening. once I got the carb off (during which I learned that there are no shortcuts to this) I was able to disassemble and see a squeaky clean carb with a rotten cork float, stuck electromagnetic actuator for the choke, and the secondary needle with a terrible gasket meeting the float bowl. Cleaning the electric choke electromagnet and reseating seeing it bounce on its spring rather than sitting idly by like a jerk, I felt like I was in a good place to reassemble since I didn't have a rebuild kit handy. At least the gaskets looked brand new.

After reassembly, the motor WANTED TO CATCH, but wouldn't. some throttle manipulation and it finally fired up! It was idling poorly and likely needs some fuel tuning. But I noticed only mist coming out of the ejection port and the idle was bugging me. I pulled the spark plugs to find threads coming off on my top plug. This was a bad deal.... Turns out AutoZone carries spark plug repair tools that if you use correctly, are supposed to work. I didn't. The reamer/tap kinda drifted sideways on me at the last 1/8" and might have gotten me into more parts. After putting the spark plug back in, we got it to idle but the top cylinder was blowing air out if it past the spark plug. I figured, since it's already jacked up, just crank it down a little more. I did, air stopped, motor idled.. yay!

Unfortunately I could not get more than a mist out of the exhaust so I was not going to put the boat in the water. Additionally I cannot move my throttle into "SLOW". Just start (and with some motivation) FAST. I looked at linkages, throttle rod, whatever the ring is that prevents throttled fwd/reverse changes and found no reason why it will not go to slow. Even using the manual throttle knob on the motor, it won't budge into slow.

At this point I had to leave, but had a great time working on the boat with my dad and his buddy. I have been looking for a replacement cylinder head, and an impeller to hopefully get the two of three remaining issues sorted over the next couple of weeks. Any input/advice would be appreciated. I've gained a lot lurking, over the past two days during this ordeal, on here and decided to register today. Thanks for any insight!
 

Drummermike58

Cadet
Thread starter
Joined
May 27, 2018
Messages
6
I'm in Northern Va...

After a little more research it appears that flaky paint is indicative of overheating. Maybe I got blessing in disguise needing a new head due to the spark plug hole issue! Pretty sure if it over heats, like car heads, it will warp.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
If that is your motor running then there are some issues I believe.
 

Drummermike58

Cadet
Thread starter
Joined
May 27, 2018
Messages
6
Yup that’s my motor. I’m suspecting low compression on top piston due to spark plug threads poorly repaired and impeller replacement to get water flow.... and carb refresh.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I hear a rattle.----I repaired a lot of those very good motors years ago.-----Do not remember them sounding like yours.------There is work to do here.
 

Drummermike58

Cadet
Thread starter
Joined
May 27, 2018
Messages
6
I heard that as well, thought it was the escaping pops from poorly seating spark plug (like when exhaust manifold gaskets fail on older v-8s but smaller in this case) or pre-detonation/ping from running lean due to untuned fueling.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Remove bypass covers on port side of block.---Inspect pistons and rings.
 
Top