1962 Evinrude Lark IV 40hp

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Going to start my carb and lower rebuild. Only thing I don't know is how to set the float in the carb. Anyone one have some insight? Thank you!
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Turn carb body & float upside down. Float should be parallel with carb body.
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
Once you have the carb back together, turn the carb right-side-up and blow into the fuel inlet pipe. Air should pass. Now turn the carb upside-down and repeat - no air should pass.
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Seems like I opened up a can of worms. I opened the side with the diaphragm and spring. How do I get it all back togehter. Also, there is a recoil type setup inside. Do I preload that spring too?
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
It is the automatic choke. Just put it back together the way it came apart, no magic there. The "recoil" spring is a bi-metal coil that expands / rotates when heated or cooled. It should have just slight tension on it with choke closed at room temp. The screw holes are slotted to allow you to adjust it ("play with it"). The diaphragm is an unloader that partially opens the choke when the engine starts, to prevent flooding and stalling.
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Well the carb was a breeze. But now the lower is giving me problems. Started with a broken bolt in the shift rod access panel. Was hoping that my drive shaft wouldn't be stuck in the powerhead and lucked out. I'd trade what is happening for a stuck driveshaft . Only 2 bolts in the impeller housing one snapped and the other is stuck. Pinion holder is broken and the pinion came out WITH a busted bearing. Anyone have the measurements of the pinion bearing? Ebay wants $70
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
not a good technical answer for you, but sounds like you are dealing with salt water corrosion. While working on your current unit, you might look for another lower unit (IMO). Manual unit, if that's your model, probably '62 to '66 -- probably more. Try for a freshwater donor. While working on the current unit, thoroughly soak the bolts with penetrating oil, pb blaster or similar, or ATF before additional disassembly. You might be able to save that impeller housing. If you are talking about the bearing assembly down under the seal, under the impeller, think the gearcase might be in bad shape (the bearing is available, believe about $40). Drain the lower unit, if you haven't already, and see what's in there. Don't take it apart yet.
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Now I'm wondering it that bearing is held together. Or are the pins loose
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
well, it would be a bearing assembly #378578 (check me on that), if it's the part you are describing -- shouldn't have loose pins/rollers. If corrosion is bad enough to disintegrate that part, not great. don't mean to be pessimistic. Is there a crack in the housing? water intrusion somewhere, appears.
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
376858, turns out it's the lower one. Just ran into a thread that said it's a loose pin bearing. Thank you for your help
 

candyman206

Cadet
Thread starter
Joined
Aug 18, 2015
Messages
23
Ok update, after hours of new curse words. I have finally taken out all broken and intact bolts. Waiting on a few parts and I will assemble.
 
Top