1960 10hp Evinrude Hesitates

carl2782

Seaman Apprentice
Thread starter
Joined
Jun 1, 2016
Messages
30
Hi, got a 1960 Evinrude Fastwin 10hp that I just did the lower unit, water pump and carb on. Was hoping that the carb clean would help it with hesitating between idle and WOT when accelerating, but it still seems to be an issue after adjusting the carb settings. If I go straight to WOT and then back off to lower RPM it runs fine. Read a few threads here and I was thinking it might be sync of carb butterfly opening with timing advance, or maybe some other ignition issue. Any suggestions where to start?
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
saying you changed l.u. oil and changed impeller, yes? What was your procedure for cleaning the carb?

test spark with an adjustable tester, and check compression -- good to post finding on both of those.

easy to do the sync, so should do that. Also, make sure the carb needles aren't vibrating loose when running (snug jam nuts -- should be just tight enough to hold needles in place, but allow some adjustment.)

[edit. fresh fuel -- insure no water in fuel.]
 
Last edited:

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
To synch magneto to carb, adjust the cam by loosening the two bolts (underneath). Adjust the cam in or out until the follower (roller) just starts to move the carb butterfly when the follower hits the scribe mark on the cam.
 

carl2782

Seaman Apprentice
Thread starter
Joined
Jun 1, 2016
Messages
30
Thanks for the responses. LU oil and seals were changed, as well as full new water pump kit. Fuel is new too. Carb was taken off the motor to bench, fully stripped down, soaked and cleaned before reassembly. Needles are tight in the glands. Just tested compression and it was low (60psi) but even across cylinders. The thing with that is, it was a loaner tester and all my motors were similarly low - so I need to get a different tester and do again. It starts great and runs well at WOT and when backing off from WOT.

Lastly I need to get hold of a spark tester and do that, but in the meantime I'll have a go at the sync and see if anything is off there. At least if it all seems good to begin with I'll know that wasn't the issue. Cheers!
 

lindy46

Captain
Joined
Nov 27, 2008
Messages
3,886
I wouldn't worry about compression. My 1963 QD23 has the same compression and runs great. Yes, do a link and sync and see how she runs. If it still hesitates, get a carb kit and do a proper cleaning/rebuild.
 

carl2782

Seaman Apprentice
Thread starter
Joined
Jun 1, 2016
Messages
30
Sorry, should have mentioned I did put a carb kit in it when I cleaned and rebuilt it. Took a look at the sync this afternoon, the roller rests on the cam right on the mark, but it has a little slack so the carb butterfly shaft doesn't actually start to rotate until the cam advances another half inch or so. Is that normal and designed for, or should I be adjusting so the butterfly actually rotates when the roller passes the mark?
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
Loosen the right screw (looking at it from the front) underneath, and pull the cam out a touch, so that the carb butterfly actually starts to move when the roller aligns with the hash mark.

Also, what is your model number? You say 10hp, but also say fastwin. A fastwin is a 18hp. The 10hp is the sportwin. Just trying to verify what motor you have there.
 

carl2782

Seaman Apprentice
Thread starter
Joined
Jun 1, 2016
Messages
30
Yeah sorry, it's a Sportwin. Great I'll do the cam adjustment and see how she runs next time I can get to the lake. Thanks!
 
Top