Search results

  1. tboltmike

    I/O vs. Outboard HP rating

    Re: I/O vs. Outboard HP rating
  2. tboltmike

    PVC for Bunk Skids?

    Was thinking about using thin wall thickness PVC sewer pipe to cover my trailer bunks. Should be easy to saw out a section and use a hot air gun to flaten and bend over the sides of the board and screw in the side of the bunk board. Passed the idea by a buddy and he thinks PVC is too hard and...
  3. tboltmike

    Electric Boat Trailer Winches

    Does anyone use these to winch in their boats? I haven't seen posts on these. I don't like to sink my hubs, but it makes for a long winch in. Luckily my rig came with a Power Winch that I have gotten spoiled in using. However, it is getting long in the tooth. I would make life simpler to...
  4. tboltmike

    Prop Upgrade Pitch Question

    I have a 2009 130 ETEC on my 17.4' by 7' beam trihull. Total weight engine, fuel, persons, gear is about 1700 lbs. I am using the prop from the original 1975 115 HP Johnnie, 13" x 17"p, 3 blade stainless. That engine WOT was about 5200 rpm and 38 mph. This prop on the ETEC pushes 45 mph at...
  5. tboltmike

    Annoying Pop Ups

    Every time I change pages a pop up appears at the bottom of the site page. This is the only site that I see this. Any solutions?
  6. tboltmike

    Trailer Transom Bunk Supports

    Re: Trailer Transom Bunk Supports The bunks will replace the angled aft rollers and a piece will bridge between the angled bunks to support the flat keel.
  7. tboltmike

    Trailer Transom Bunk Supports

    I'm transitioning from rollers to bunks. The trailer cross beam is a 3 inch tall channel with legs facing toward the front of the trailer. The 12 inch wide transom roller brackets were U-bolted to the cross beam. I am planning on using 4x4's as the transom bunk, one either side of the keel...
  8. tboltmike

    Choosing Diameter

    What is the relation between pitch and Diameter? What is the criteria for selecting diameter? Seems like for a given engine there are ranges of diameters and pitches. Does going up in diameter for a given pitch have the same affect as increasing pitch? Does speed and economy enter the...
  9. tboltmike

    Battery Disconnect Switch Exposure to Saltwater Spray

    I have been looking at these switches on line and cannot find information on their resistance to a saltwater environment. The only convenient place to locate one on my boat is on the side of the splash well above where the motor leads and cables enter the boat interior. However, this is...
  10. tboltmike

    Old Prop on New Engine?

    I just replaced the original engine on my 18' trihull, 1100 lbs dry. The prop is a 3 blade 13 x 18 pitch that came with old 1975 115 Johnnie. It pushed the boat 39 mph at 5200 On the new 130 ETEC, it turns 5800 she goes 42 with 4 souls, bimini up and a stiff breeze and 46 at 5800 with 2 on...
  11. tboltmike

    130 ETEC Development

    Is there any technology developments between a 2009 and 2012 models? Is 2009 have mechancial throttle/gear shift cables are fly by wire? I've looked at the parts section on this site and Evinrude and cannot find the control systems shown.
  12. tboltmike

    2009 Etec 130

    Have an opportunity for a new 2009, 130 Etec still in the box at a 10% discount. Are there any improvements on newer models that would off set the savings?
  13. tboltmike

    New Engine, What is Included?

    I have heard that the price of a new ETEC does not include oil tank, controls, prop. If so, what are typical prices of these? Thanks, Mike
  14. tboltmike

    New Engine On Old Boat

    Looks like my '75, 115 Johnnie is near wear out mode, low compression on all cylinders and has developed a carb problem. This is the original engine for my Arrow Glass Cheetah, which I have just finished a restore. I like the boat and the engine, for that matter. The engine has never let me...
  15. tboltmike

    Dead Cylinder, '75. 115

    Had her out seveal times this summer and everything normal. Ran it on hose before taking it out a week after the last outing and it just sounded strange. Cranked up ok and idled and didn't sound like a miss. Started pulling plugs and #2 was room temp. Inspected plugs, gapped and swapped...
  16. tboltmike

    Dead Cylinder, '75. 115

    Had her out seveal times this summer and everything normal. Ran it on hose before taking it out a week after the last outing and it just sounded strange. Cranked up ok and idled and didn't sound like a miss. Started pulling plugs and #2 was room temp. Inspected plugs, gapped and swapped...
  17. tboltmike

    Fuel Filter Leaks

    I've had a spin on fuel filter installed for several years with no problems. It is one with the clear cap and drain on the bottom. This week when the cartridge was replace the o-ring seal leaked. The cap and ring was inspected prior to assembly and after leak and no damage was seen. It was...
  18. tboltmike

    LED Tail Lights, Not all burning

    I bought a LED kit for my boat trailer about 2 years ago. The boat is in a restore mode and the lights have only been to the launch about 4 times and have never been in the water. it was last used about 3 months ago and the lights were ok. This time I noticed that on the right lite, 2 of the...
  19. tboltmike

    Sunglasses Selection

    The wife wanted to get me up=scale SG's but didn't have a clue was to which to pick. Althought I use SG's they are usually the $15 ones that some pro endorses. I/ve spent three days arguing with myself about: Color, Tint, Mirror, Glass. Plastic, 580, 400, and the list goes on The < $90 ones...
  20. tboltmike

    How to save fuel? cruising speed the only way?

    Re: How to save fuel? cruising speed the only way? This is the perfromance data from my trihull using the Lowrance fuel mgemt system. It was under favorable condition and light load. Will do another with more load. Scroll down page for chart.
Top