Search results

  1. O

    1995 2.5hp mariner, initial idle screw adjustment

    Looking to find a initial idle screw ajustment, and float adjustment for the above motor, serial number is a D series. Thanks in advance.
  2. O

    1985 9.9 johnson outboard

    looking for a part that is not listed on the parts list, Its the a plstic part that linkage fron the shifter that prevents the motor from starting in gear the part # appears to be 323657. Thats the # on the part, if anyone knows of used part site that can help with this it would be great. Thanks
  3. O

    9.9 johnson ignition question

    Its a 1985 9.9 johnson, I aquired it recently an looking at the timing base there was a stainless L shaped piece loose, I can't seem to find it in the part diagrams for its former location. Can anybody give me some insite. Thanks in advance.
  4. O

    1975 9.90 evinrude question

    I have a 1975 9.90 evinrude runs great except for a overheating problem. Have replaced t-stat, water pump. Did not help, pulled lower unit off 2 times since to check that was not the problem, then changed the t-stat no change. My thoughts are the seal at the top of the water tube to the...
  5. O

    Montgomery Ward outboard

    Model#vwb27906b 86x, sn#20222. What year and hp? motor runs only if you keep pumping the bulb, any thoughts on parts fuel pump and sources. thank you
  6. O

    what does this timing base fit

    I have a timing base, I think its for a saildrive but dont know yr model, oem # 583289, I also have a power pack #581895. Any help or direction to find out would be great. Thanks
  7. O

    1975 evinrude 9.9 overheating

    I have replaced waterpump, thermosat, motor starts right up and will idle in tank for hours. When increase rpms it starts to overheat. This has never seen salt water, any ideas. Thankyou
  8. O

    Interlux Brightsides question

    I'm having problems using the roller and tip method on a fiberglass boat on vertical surfaces. Can't a smooth surface going by all prep and info on the Interlux web site. Has anyone tried hvlp or airless on this paint, and what kind of results.
  9. O

    overheating 9.9 rude

    I have a 1975 9.9 evinrude, install new water pump assembly. started it up could see small amount of water discharge till it warmed up and overheated. Could this be a stuck t-stat or a water passage problem. I pulled the lower unit again and checked where the tube slips in the grommet, and it...
  10. O

    removing water control on 1986 140 rude

    I've instralled the newer thermostat caps, gaskets and spring s on my 1986 140. I removed the water control on the thottle, my question is this.. The water control vale had 3 lines connected to it, 1 goes to the tell tale. 2nd one went to the old thermostat caps(been removed). the 3rd went to...
  11. O

    deck work on Spirit 28 sail boat

    I have a 1980 spirit 28, due to leaking mast shrouds I have sot areas of decking. The deck appears to be outer layer of ployer with a layer of wood, 1/4" or less between outer and inner layers. I have repaired leaks to shrouds with a thickened expoxy, any body tried to replace rotted wood for...
  12. O

    new style t-sats on a 1986 140 looper

    I would like to remove the water control on the throttle and install a newer t-stat set up on this motor, does anyne know the parts to order or is the parts off a 1995 looper would work. Thanks for any input in advanced.
  13. O

    dhadley help pls on 1986 140 evinrude

    I posted a while ago on changing the carbs on a 140hp 1986, I installed the 1995 130 cabs and bodies and fit perfect. I left the jetting the same as the the new carbs. My question is I'm having trouble with a cold start, The solenoid works but I have to add more fuel with the box off to get it...
  14. O

    1995 130 evinrude carb question

    rebuilding carbs, mixed up the location of the mid and idle air jets. is the idle the upper location or the lower?
  15. O

    1986 140 carb change evinrude

    Need to change carbs on my 140 due to cracks and tubes. I have 1995 130 carbs wih throttle bodies and air box with linkage. The throttle bodies and carbs have the same bor as the originals. Just the air jets and mains are differant. The other differance is the idle screw on the top left of...
  16. O

    still fighting bogging 86 140 rude

    Like Brew2 still fighting bogging in midrange, idles, top end great. My question is the emulsion tubes in the center of the carbs, I have (2) carbs that the tubes appear to rising out of the carb body at differant heights. About a 1/16" of a inch. Is this normal? Or has someone over yhe years...
  17. O

    1986 140 rude question

    does each carb corresponde to that cylinder or does the passage way after the reeds, cross over to the opposite side
  18. O

    carb replacement for 1986 rude 140hp

    I need to replace carbs on this motor due corrision on tubes. I found a set from I believe was a 90,s 130hp, also a lopper. The carbs come with throttle bodys, linkage and air box. will these fit the 140hp?
Top