Search results

  1. T

    Slickcraft questions

    Hi all, I have a couple questions re: Slickcraft boats, specifically the SS 235. 1) the listed weight is 3160 lbs dry, does this seem accurate? 2) what top speeds have you observed? I realize there are numerous engine drive configurations, so please include engine & hp. Thanks in advance, TC
  2. T

    Help! On vacation ! 1970 115 pulse pack

    I got this motor about 3 years ago, and had to replace pulse pack after just a few hours use. I replaced with CDI pulse pack # 113-8362. Also replaced rectifier & coil. Now it's blown again (it wouldn't start, and pulse pack was literally smoking). Last time I had the luxury of time to...
  3. T

    Install pressure gauge

    I 'd like to add a pressure gauge for my 1970 115. No tell-tale. There's a plug on side of #1 cylinder (circled in attached pic). Is this a cooling water port? Thanks, TC
  4. T

    temp & pressure gauges for 1970 115

    I'd like to install temp and pressure gauges on my 1970 115. Can anyone tell me the simplest way to install to this engine? Also, I'd like to install a tach...12 pole? Thanks! TC
  5. T

    Prop ID JP81

    1970 Johnson 115 - I bought it used. It came w/ a spare prop. Only markings are:<br /><br />Michigan JP81<br /><br />Can anyone tell me the pitch?<br /><br />Thanks,<br /><br />TC
  6. T

    Method for determining prop pitch?

    I have a spare prop that came with my used Johnson 115 (1970). It has NO discernible markings. I know it fits, but I don't know the pitch.<br />How can I determine the pitch?<br /><br />Thanks,<br /><br />TC
  7. T

    Denso sparkplugs

    Any opinions on Denso sparkplugs?<br /><br />Thanks,<br /><br />TC
  8. T

    Denso sparkplugs

    Any opinions on Denso sparkplugs?<br /><br />Thanks,<br /><br />TC
  9. T

    1970 115 won't shut off

    First it wouldn't start.<br />I found some bad wiring on rectifier, which, I think, caused pulse pack to go. I replaced both, along with coil. Starts right up now, but won't shut off. It did this once before, but choked motor to kill it and cycled switch a few times (Motor hadn't been run in a...
  10. T

    Add water pressure gauge to 1970 115

    I'd like to add a water pressure gauge to my 1970 115. Can I just splice a tee into one of the water hoses between thermostat housing and block?<br />Also, what pressures should I be looking for?<br /><br />Thanks,<br /><br />TC
  11. T

    Impeller replacement 1970 115

    The parts breakdown (BRP site)shows no gaskets above or below impeller plate (or anywhere under housing for that matter). Is this correct? The only impeller I've replaced was a Merc, which had gaskets above and below plate, IIRC.<br />If no gaskets, then I would only need:<br /><br...
  12. T

    Water pump kit for 1970 115

    I've been searching online for a water pump kit for my 1970 115. I've found impellers, but not the whole kit (impeller, gaskets, etc). Are the kits still available? Any hints where I could find one online?<br /><br />Thanks,<br /><br />TC
  13. T

    stator stuck to distributor

    1970 Johnson 115. I need to remove stator (to unscrew coil wire - I'm replacing coil and pulse pack)and the stator is stuck to distributor. Any tips on seperating them? <br /><br />Thanks,<br /><br />TC
Top