Search results

  1. B

    Gap specs for 757HA '73 Chrysler 75HP?

    Did a search but did not find it. I am replacing my points and need to know the gap. My manual is at my buddys house an hour away. I believe it is .014. Any help guys?
  2. B

    Will carbs from a '82 75HP fit a '74 75HP?

    Does anyone know if the carbs from a 1982 75HP Chrysler will fit a '73-'74 75HP model 757HA? Don't know exact model of the '82 Thanks
  3. B

    What type of gas?

    Just curious what octane y'all run in your Chrysler/Force motors? <br />I have always ran regular 87 octane with no problems, but was wondering if switching to premium would yield any advantages i.e. less carbon build up, more power etc, <br />Or if there were any downsides to running premium...
  4. B

    Thanks for the Help!

    Check it out<br /><br />Would like to see something like is in Chrysler/Force forum <br /><br /> http://www.iboats.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=28;t=028444;p=1
  5. B

    Should I be getting water out of telltale at WOT?

    Just got done replacing my powerhead, and impeller -- Took the boat out last nite to test it out- Was getting water out of telltale at idle, but at WOT there was no water coming out of the telltale. I put my hand over it and felt a slight vaccuum at WOT. When I was idling and water was coming...
  6. B

    Distributor/timing belt? 75hp chrysler

    Motor 75hp 1974 chrysler 757ha<br /><br />Anyone out there know if napa carries these belts merc part # 57-F85311
  7. B

    Flywheel Removal ? Tips?

    1974 75hp chrysler 757ha <br /><br />Ok so I am pretty far into replacing my powerhead, got the new (used) powerhead on the motor leg and almost everything on but now I have to put on the distibutor belt so I have to pull the flywheel -- <br /><br />What is a good way to get the nut off the...
  8. B

    Gaskets, which ones?

    1974 chrysler 75hp --757HA<br />I am replacing my impeller and my powerhead (costly mistake :D ) and have some questions on gaskets needed. First of all when I replace my impeller, do I need to replace the driveshaft seal that sits in the top of the water pump housing? Second do I need to...
  9. B

    Pics of my Boat (project)

    Tell me what y'all think Good or bad....<br />Here are a few pics of my boat- 1974 Higgscraft 14' trihull with 75hp Chrysler. I will post higher res ones soon, these are all from my camera phone.
  10. B

    Overheat--

    Yesterday Had the boat out -- Running fine for first hour -- stopped at a park and ate lunch-- Then ran it for about 5 minutes and it died-- when I turned the key back to "on" the buzzer was going off -- waited about thirty minutes for it to coll off -- started it back up and was getting water...
  11. B

    Water In Boat -- ??

    Last time I took my boat out- as soon as I got it in the water and got in the boat I noticed the carpet was wet near the drivers seatfloor-- Drove it for a couple of hours and it got a little worse-- most of the carpet was wet. Once I got it back on the trailer I couldn't find any scrapes or...
  12. B

    Higgscraft Boat Any Info?

    I just purchased a 1974 Higgscraft Boat with a chrysler '74 75hp-- The manufacturer is higginbotham co. I have so far been unable to find any info out on the brand of boat. It was manufactured in Austin Tx, which is where I live and where I purchased it. It is in great shape. But when I look...
Top