Search results

  1. C

    model #

    The tag that indicates model# & serial # is faded out on my 1989 85hp force,Any body know a way of determing model#?All i have is motor id# on title.
  2. C

    Stupid question part 2

    To add to my stupid question on monday 8th,just letting every body know,I droped the lower unit yesterday,the impell was completely shot,I took out the thermostat and ran some water down from the head and wasnt getting any water ouy the water tube,it was stoped up,washed it out from the bottom...
  3. C

    stupid question

    I aquired a 1989 85hp force about 7 months ago<br />This motor has been setting for about 1 1/2 years<br />I finally got around to messing with it,put it on a stand,hooked up fuel tank,and ignition switch,Started right up ran for 10-15 sec and i killed it cause i dont have any water peeing...
  4. C

    ignition switch

    I have a 1989 85hp force,I have it on an engine stand,this is a spare motor,Does any body know witch wires i need to hook to the switch from the harness just to start it? there are 6 wires coming off the switch 7 wires coming from the harness,all the colors from the switch dont match all the...
  5. C

    GEL COAT CHIPED

    I have some deep scratches and chips on the bow of my boat,looks like preveious owner needed to replace bow stop but instead kept nocking the bow<br />against the metal channel.I replaced the bow stop<br />but would like to repair the scratches.What would be the best way to fill in these...
  6. C

    BATTERY CHARGING

    I recently bought a battery charger black&decker<br />reading thru charging instruction,it says for marine batteries to remove from boat and charge on shore,it dosent say why,Does any body know why you would have to do this,and if not should you disconnect the cabels befor charging or can you...
  7. C

    Installed water pump..but

    I put a water pump kit and few other o-rings in my 1981 evinrud 90hp replaced the shift rod o ring,cause it was leaking water in lu.Any way every thing works great but when i pulled it out of the water i noticed one spot at the front leaking water between the lower uint and the mid section,since...
  8. C

    Lower unit shift rod

    On an 81' 90hp evinrude model# E90TLCIM,Can any body tell me where to disconnet the shift rod so i can remove lower unit? any help would be great.
  9. C

    81' EVINRUDE WOT ?

    I have an 81'90hp V4 rude,right after boat planes out and about to achieve top speed engine boggs down slighty,ican tell ther is alittle loss of power and rpm,if i throttel back bit it will pick back up and run fine,but as soon as i go to wot is runs fine for a minut the boggs down again,but...
  10. C

    Lower unit

    I recently got a 1981 90 hp evinrude,runs good but has been out use for some time,im going to replace the water pump impeller,but i've been geting a little water in my oil,I replaced the seals in the fill/drain plugs but still get water.I want to replace all the lower unit seals while i got it...
  11. C

    PARTS MOTOR

    I GOT A 1981 150HP MERCURY W/POWER TILT/TRIM & CONTROLS,IM WANTING TO SELL,DOES ANY BODY KNOW OF ANY PLACE IN THE DALLAS FORT WORTH AREA THAT MIGHT BE INTRESTED IN IT.
  12. C

    12/24 VOLT WIRING ?

    Trying to hook up a Motorguide 12/24 volt,<br />the motor has 3 wires red,black,white,the way i under stand it is the red goes to + on battery A<br />the black to - on battery B and a jumper from - A<br />to + on B,so where does the white one go? Tried toget info on motororguide site, but only...
  13. C

    MIAN PLUG WIRE HARNESS

    I GOT A 1981 90HP EVINRUDE,I GOT PAOWER TO THE STARTER CYLINOID AND TO THE TERMINAL BLOCK ON THE ENGINE ,BUT DONT HAVE POWER TO THE MAIN PLUG HARNESS THAT PLUGS UP TO THE COMMAND CENTER,ANY IDEALS ON WHER TO START?
  14. C

    LOWER UNIT BOLTS

    I've got 1981 90hp evinrude,i am going to replace<br />water pump impeller,there is 4 bolts in front 1 in back,my question is ,is there a bolt hidden under the trimtap,icant break loose the bolt holding the trimtab on,and dont want to break it off if there is no need to remove the trimtab<br...
  15. C

    Primer woes

    Going to repaint my 81'evinrude 90hp .Witch is better for primering, Etching aluminum paint,or Zinc chromate primer?<br />Does any know?
  16. C

    Another Gel-coat ?

    I've read some of the other fourms on gel-coat<br />restoration,using Comet,scotch brite pads,buffing compounds,to remove the oxidiation,and bring back shine,Is this process also recommended for Metalflake paint/gel-coat as well? Any help would be great. Thanks
  17. C

    OUTBOARD REPAINTING

    Can i use the the same omc paint for lower units<br />om my fiberglass engine cowling, if not what is the best paint for the cowling?
Top