Search results

  1. DJK555

    Owners Manual Search

    Looking for an Owner's Manual for a 1989 CE4RDHCE. Suggestions? Thanks.
  2. DJK555

    3.0 exhaust manifold question.

    1994 3.0LX. Replaced riser and gasket. cleaned and cleaned mounting surface of manifold as manifold internal ports looked good. Water is obviously leaking out of the joint. The questions are: can this leak put enough water into the bilge when running for an hour or so to have the bilge pump come...
  3. DJK555

    Which Sealant?

    I'm refinishing a hatch cover from a Nordic Tug that has a clear Lexan/polycarbonate insert. The insert was sealed with what appears to be clear silicone. Is silicone the best sealer for this or is there a better product?
  4. DJK555

    Mercruiseer Prop Hub removal

    Thanks. What should I look for in terms of a Hub Kit for Prop 2?
  5. DJK555

    Mercruiseer Prop Hub removal

    I'm trying to replace a prop on a 3.0L Mercruiser with an Alpha 2 leg with one that came with the boat. Identical props but one has had very little use and is in good shape. How do I remove the hub in the current prop? I assume they are made to be changed.
  6. DJK555

    Bellows Adhesive application

    Mercruiser Service Manual Number 13 - Marine Engines GM 4 cylinder
  7. DJK555

    Bellows Adhesive application

    I'm replacing the exhaust flapper on a 3.0L Mercruiser. The manual calls for the use of bellows adhesive on the rubber boots that connect the upper and lower exhaust tube, and I assume, on the boot that connects to the riser. Is the adhesive required in this application and if so what is its...
  8. DJK555

    Service Manual

    Some time ago I followed a post that provided a link to a Mercruiser Sevice manual Number 13 - GM 4 Cylinder. That was a great help. Is a link available to that series of manuals but covering Bravo Gen ii stern drives?
  9. DJK555

    3.0L Mercruiser timing adjustment

    I'm sure this has been covered before but I can't find a direct answer through a search. 1994 3.0L with EST distributor. When adjusting timing as per manual instructions the timing does not revert to base when the two white leads on the distributor are jumped. Also, the instructions state that...
  10. DJK555

    Sourcing Mercruiser Cooling Hoses

    Looking for suggestions for a source for cooling system hoses for a 3.0LX serial number range 0F604000 - 0K999999 with fresh water cooling. I have part numbers that should be accurate: 32-96763, 32-96766, 32,96765, 32-815413 but am not able to find any Mercruiser parts sites that list these...
  11. DJK555

    Cooling hose identification

    Does anyone know of a link to a site with cooling hose diagrams and OEM or Sierra part numbers? I'm trying to find an online supplier but need to identify my hosed by part number. I'm working on a 1994 3.0LX.
  12. DJK555

    Mercarb question

    Re a 1994 3.0LX carburetor. I'm calling it a Mercarb rather than a Rochester because it has one mixture screw. Numbers on the Carb are 05924A-1 / 3 01. I recently rebuilt it using a Sierra Kit #18-7097 which replaces the 3302-9437. I am not 100% sure that this is the exact kit but it was close...
  13. DJK555

    Mercarb question.

    I'm looking for some advise on a accelerator pump plunger for a Mercarb. It's on a 1994 3.0LX. The number on the carb is 05924A-1 / 3-01. According to my local dealer that carb calls for a Sierra 18-7097 kit. Everything in the kit matched up except for the accelerator pump. There were two...
  14. DJK555

    Bilge pump discharge?

    Mercruiser 3.0 in a Campion 185. I replaced the bilge pump but can’t locate the exit point. I can fill the bilge with water and look for the discharge but was hoping someone could tell me where the exit point is. I can follow the corrugated hose back to the rear-centre of the bilge but can’t...
  15. DJK555

    Two lower leg questions

    RE Alpha 1 Gen 2. Problem 1. I installed the lower leg after replacing the impeller with a full kit. Installed new gear oil. Ran engine on muffs. Very little water coming out of the prop. Checked water flow at the hose leading to the HX. No flow other than a few spurts. Engine came close to...
  16. DJK555

    More trim gauge questions......looking for some basic info.

    1994 3.0 L Alpha one Gen 2. Recently bought a boat that is in pretty decent shape but the trim gauge is not working. I’ve searched past threads on this and other forums and have a fair understanding of the operation. All components appear to be good. The sender was replaced at some point. It was...
Top