Search results

  1. Chryslerman123

    Chrysler 30hp impeller

    EDIT *Typed part number incorrectly in original post*
  2. Chryslerman123

    Chrysler 30hp impeller

    I have a 1979 Chrysler 30hp model 302H9C and need an impeller. All parts manuals and diagrams say it takes Sierra 18-3901/Mercury 47-F462065 and that is not the correct one because the driveshaft hole is 5/8 on those. My driveshaft is 9/16. The old impeller is 6 vanes with a plastic insert...
  3. Chryslerman123

    1975 25HP thermostat

    Thank you both so much! I’ve been stressing about it and I’m glad to know it doesn’t need it
  4. Chryslerman123

    1975 25HP thermostat

    I was kinda thinking that because my 20hp Chrysler doesn’t have one or even have a place for one so it couldn’t be incredibly important on a 25 I would suppose. I just don’t want to damage anything. Someone has had the thermostat cover off before because it had non stainless steel grade 2 screws...
  5. Chryslerman123

    1975 25HP thermostat

    I have a 1975 25hp 257HA. While figuring out why it’s not pumping water I decided to check the thermostat, turns out someone removed it who knows how long ago. It was made with a thermostat and i intend to replace it. I know the thermostat for this engine was discontinued long ago and I can’t...
  6. Chryslerman123

    Chrysler 25hp coils

    Do i need 6 volt coils or 12 volt? It has one of each on it right now
  7. Chryslerman123

    Chrysler 25hp coils

    I have a 1975 chrysler 25hp 257HA with the battery ignition and the stator alternator. The external coils are on top of the head. I’m doing a cosmetic restoration on this nice engine and want to get new coils because the old ones are from who knows what and the wiring someone done is terrible...
  8. Chryslerman123

    Sea King 9.2hp will not Spark

    I believe the part number for the condensers is Sierra 18-5241
  9. Chryslerman123

    Sea King 9.2hp will not Spark

    Parts are obsolete I think the condenser is actually the only ignition part you can still purchase. Did you clean the points? That almost always works to get fire to the plugs.
  10. Chryslerman123

    tilt pin

    you can drill a hole in the other end and put a cotter pin through it so it doesn’t fall out. Need a center punch and a drill press i’ve done it to several pins before.
  11. Chryslerman123

    Chrysler direct drive lower unit

    I was given a Chrysler direct drive lower unit today. I would like to put it in use but it will need new seals and a prop. Does anyone know anything about these? Also what horsepower will this fit? I think it is extremely rare?
  12. Chryslerman123

    Chrysler 130hp clutch dog

    Will the clutch dog out of a Chrysler 130hp work in the lower unit of a Chrysler 85hp? Thanks
  13. Chryslerman123

    130hp clutch dog

    Will the clutch dog out of a Chrysler 130hp work in the lower unit of a Chrysler 85hp? Thanks
  14. Chryslerman123

    Wizard super twin fuel tank and water pump

    I a wizard super twin model#w64. Horsepower is unknown. It's in decent condition and I would like to get it running. I cannot get the gas tank off. Theres two studs underneath I think those are the only thing that hold it on but it wont budge. I also have no idea where the impeller is located...
  15. Chryslerman123

    lower unit driveshaft seal

    I have a chrysler 20hp and a 9.9hp. The lower unit driveshaft seal is leaky on both of them. They both have the same seal. I would like to replace the seal without buying the whole seal kit. I need the sierra part number for the seal if they offer it individually. The outside diameter is 1 inch...
  16. Chryslerman123

    1971 chrysler 20hp outboard acceleration issue

    My chrysler 20hp outboard starts in one pull and runs excellent at idle. Plenty of blue smoke. When I give it full throttle, it does not accelerate at first. It sputters/jumps like it wants to accelerate but it doesn't. It sometimes takes 5-10 minutes before you can get it to go. Once you get it...
  17. Chryslerman123

    Using copper anti-seize on spark plug threads

    I recently installed new spark plugs in my: Chrysler Outboard with aluminum head lawnmower with a magnesium head, Honda Accord with aluminum head, And my Chevrolet truck with steel heads. I used permatex copper anti-seize on all of those spark plugs. Now people are telling me that I should not...
  18. Chryslerman123

    Taking jon boat out in cold water

    I recently purchased a 1976 loweline 14ft jon boat. I put on my chrysler 20 hp outboard that I got running. It is cold here in Kentucky but I really want to go test run my boat and make sure my outboard runs ok. I planned to wait until spring but I am just too anxious to wait. I am an...
  19. Chryslerman123

    LoweLine 1436 jon boat specs

    I recently purchased a 1976 Loweline 1436 jon boat. The coast guard specifications sticker is missing and I am wondering what the max weight capacity and the max hp rating is. Thanks.
  20. Chryslerman123

    Bass boat steering conversion

    Is it ok to remove the steering console from a small bass boat(14-16ft) and convert it to tiller steering to add more space? I found an old chrysler bass boat and would like to basically strip it down completely and just have an empty floor with a couple seats, nothing else.
Top