Search results

  1. L

    377mag random misfire

    Our boat, with a 4.3 efi, randomly would miss on acceleration, then quickly progressed till it failed completely and would not restart. It was the ignition sensor.
  2. L

    Jumpy Tach

    Thank you sir, I'll be sure to do that while I'm there.
  3. L

    Jumpy Tach

    I guess tomorrow I'll be checking my connections, making sure they're clean and snug. Thanks, that's a good place to start.
  4. L

    Jumpy Tach

    My tachometer occasionally jumps. It's not constantly, from what I'm noticing it will do this for a few times, about once an hour or so. Any ideas on what is going on? If this is going to get worse, I'd rather be prepared for it. The video is a little jumpy, just like my tach. :) This is a 2001...
  5. L

    Mercruiser anode replacements

    LOL Yes, fresh water. I guess that's one thing I take for granted, as far as wear and tear on the material.
  6. L

    Mercruiser anode replacements

    At what point should one consider replacing anode parts on an Alpha One Gen 2 outdrive? How do these look? I have about 700 hours on it.
  7. L

    Mercruise stalls when put into gear

    Sounds different than mine.. I may be wrong, but I think you can bypass the shift interrupter, just for troubleshooting. You probably need someone more knowledgeable to chime in on that...
  8. L

    Mercruise stalls when put into gear

    How much time goes by before it will run again? Kind of sounds like mine was doing, after about 1 1/2 hours it would run again. Mine turned out to be vapor locking.
  9. L

    Mercruiser 4.3 cracked intake manifold

    I got everything squared away with the motor, and so far I've put over 3 hours on it. My oil pressure fluctuated some to start, then steadied out, and ran great this weekend. I appreciate all the help getting my boat back on the water, this is a great group. Thank you!
  10. L

    Mercruiser 4.3 cracked intake manifold

    I installed my intake manifold, and I'm on my 3rd oil change so far. Trying to think ahead, which I should've done sooner... :) I will need to check the timing, and according to the service manual there's an EFI Timing Tool that I need to use, part # 91-805747A2. It will take at least a week...
  11. L

    Mercruiser 4.3 cracked intake manifold

    Maybe this is corrosion, it is inconsistent on the bolts. I wire brushed them down, and I have a different bolt that I ran in and out of the holes to make sure they did so. I shop vac'ed the holes out.
  12. L

    Mercruiser 4.3 cracked intake manifold

    As I prepare for installing my intake and putting my boat back together, I have a few questions. 1. - My intake manifold bolts look like they had some kind of greenish looking loctite on them. Do I need to use loctite on any bolts, and what kind? (intake, distributor clamp, thermostat housing...
  13. L

    Where is the Fuel Pump/Cooler assembly on a Mercruiser 4.3L MPI?

    That check valve (P/N 21-862271A 1) is about $130, at it's cheapest, it's pricey for what it is, but worth it to help avoid vapor locking while on the water. But after being stranded a few times, and having to wait 1 1/2 hours each time for it to restart, it was worth it for me. During...
  14. L

    Where is the Fuel Pump/Cooler assembly on a Mercruiser 4.3L MPI?

    There's a water drain port for the fuel pump water cooling system, I have to crawl in the back port side, by my trim motor. You have to be half contortionist to drain it, I turn on my right side and pull a couple wires out of the way with my right hand, then work my left hand in upside down to...
  15. L

    2000 Searay vapor lock

    My 2001 SeaRay with 4.3 EFI vapor locked, I struggled with it for a couple years, took it into a couple different boat shops, then I ran across this TSB on the internet. I installed the check valve mentioned in the TSB and adjusted some of my habits, such as not shutting the engine off right...
  16. L

    Mercruiser 4.3 cracked intake manifold

    My new intake should be here Wednesday, so I'm cleaning my gasket surfaces and looking through the manual. I got to the torque specs and it says 35 ft. lbs., then I remembered your comment. Then found the service bulletin about it. So glad you made this comment....
  17. L

    Where is the Fuel Pump/Cooler assembly on a Mercruiser 4.3L MPI?

    I have a 2001 4.3 MPI, mine is port side. In the picture, if you follow the water hose with the blue check valve on it, it should take you to it. I had to install the check valve to prevent vapor locking with my fuel pump.
  18. L

    Mercruiser 4.3 cracked intake manifold

    Not even on the thermostat or distributor gaskets? Just an FYI, I wouldn't use gasket maker on them. For some reason I thought sealant was used on one side, maybe that was mostly to keep them in place. Good to know though. I see you used to own an '86 Glastron Conroy X-19, that was our first...
  19. L

    Mercruiser 4.3 cracked intake manifold

    I bought an intake off eBay from Michigan Motorz this morning. I called Michigan Motorz to verify the intake, but they only do free shipping off ebay. I bought 3 gallons of cheap 20w50 oil, 1 gallon of 25w40 Mercury oil, 4 oil filters, and gaskets for my distributor and thermostat. Also a couple...
  20. L

    Mercruiser 4.3 cracked intake manifold

    After 3 days of draining, the sludge is about drained. I'm hoping the bearings are good, because I've decided to go that route. I'm looking for a new intake manifold (I don't see one through this site), gaskets, lots of oil, and a few filters.... So far, this is a best case scenario, and if it...
Top