Search results

  1. A

    Trouble with my trailer rigging

    I have a serious problem guys! I need to adjust my trailer so it can fit my boat. My problem is that the front of the boat at the keel where the roller hits. It became damage from the boat due from to much weight and now it's scrapping the actual trailer which is a serious problem. How do I fix...
  2. A

    Rebel 26cc by Rebel Marine??

    Anyone know anything about this boat?
  3. A

    Misfire perhaps?

    Took my boat out today just for a sec to work on my trailer. I was just giving it gas when all of sudden I hear a hissing noise for a quick second a few times. I am not sure if it's a misfire which my eyes point in that direction but I wanted to ask you guys because maybe you ran into this. I...
  4. A

    Force 125 Timing?

    Can anyone give me directions on the how to adjust timing to proper setting. I read something about 32..?? No clue...need help guys..
  5. A

    carb problem ?

    Ok guys new problem with my force 125. I went out this morning and at first took a bit to start her up but then got her going. After a while we stopped to fish and tried to crank but wouldn't turn over. Spins freely and all but when I took the cover out my friend look at it while I tried...
  6. A

    Leaning Post Project

    Hey guys, so I decided to start my leaning post project for my 18 ft wellcraft. I am tired of the captain helm seats and it's pretty much old school now a days. I had plywood in the garage and cut them to certain dimensions that was good for me. I then bought 3 quarts of resin with hardener some...
  7. A

    Steering console repair?

    I have a 89' 18 foot Wellcraft Fisherman and my steering console is broken at one part. I am not sure if anyone is familiar with these boats but the part that is broken is under the wheel and throttle where your feet is against while sitting or standing. It's cracked on the bottom and with this...
  8. A

    Force 125 shakes at low RPM

    Re: Force 125 shakes at low RPM Found this on Seloc Online Manual: 1.Remove engine cover to gain access to carburetors and link rods. 2.Set idle mixture screw to proper base setting as listed in the Carburetor Specifications chart. 3.Install a flushing device or submerse lower unit in...
  9. A

    Force 125 shakes at low RPM

    Hey guys, My force 125 shakes when it is in gear at low RPM's (1000-2000). When going faster and higher RPM's it smoothes out. Whats going on? Is it carbs or what?
  10. A

    Bad Rectifier?

    I was reading up on some threads about how to find the problem when your tachometer doesn't work. Basically they seem like all the same..could be the tach...could be a wire...could be a blown fuse? I saw to check the rectifier on the outboard and read about rectifiers. I notice that this was the...
  11. A

    Do it yourself T-Top project

    Re: Do it yourself T-Top project Change of plans...Instead of using the 1 1/4 inch I switch to a 2 in pipe and bent them today. Next up is I need to find tee connectors or somekind of connector to my base pipes to the canopy frame. Here is a picture of my somewhat finished canopy..
  12. A

    Do it yourself T-Top project

    Ok guys I have decided to make my own T-Top frame for my 18ft wellcraft. I have seen in another thread that off-peak made and he did a great job on his boat. I have always wanted to do my own thinking it really doesn't look as hard as you think. Just takes some measuring and some bending. I have...
  13. A

    Force 125 pistons?

    Re: Force 125 pistons?
  14. A

    Force 125 pistons?

    Looking to swap out a powerhead with a bad cylinder for another powerhead that seems to be in working condition and I was told it was rebuilt. My question is the guy says it has 160 lbs of compression on each cylinder except 2 that has 157. I heard 130 lbs was really good but didn't know if they...
  15. A

    Force won't turn over

    Ok guys I had my motor rebuilt. Try to crank it up nothing. Barely turns so I took the plugs out and it turns like a champ.. I put pre-mix in each cylinder to lube it and and turn it to clear it out. Put plugs back in but again nothing. It barely turns but sometimes there are times where it...
  16. A

    Force Rebuilt now won't start

    Ok rebuilt my outboard and put new gasket in. Put motor together and charged up the battery. Turn the ignition and starter pops up. Spins the flywheel a bit slows down and just stops. Not starting like it use to. I am thinking its something electricalor timing but I need help with this issue. I...
Top