Search results

  1. sutor623

    Marine vinyl adhesive

    Ahicks, Yea that’s what I resorted to. A map gas torch and a wide blade razor scraper. Took me and a buddy 7-8hrs total to get it all up. Ugh what a mess!!!
  2. sutor623

    Marine vinyl adhesive

    Well if it were a wood substrate I would do that. This boat has an aluminum deck.
  3. sutor623

    Marine vinyl adhesive

    Hello folks, I am pulling carpet off of an aluminum decked pontoon. I got all of the carpet off but the glue is being very difficult. I got it all smoothed out and was considering gluing the vinyl directly to the old glue but I dont want to risk issues in the future. There are two types of...
  4. sutor623

    Tohatsu 70 TLDI

    Hello folks, I am working on a 2004 Tohatsu 70 TLDI engine. I have all of the diag equipment for Honda, Brp, mercury, mercruiser, suzuki and yamaha. I use BRP diagnostics as well as diacom. Anyways, I do not have a way to plug up to this darn tohatsu. Fuel pump died so I put a new fuel pump...
  5. sutor623

    Looper and crossflow lower units.

    Just wondering if V4 looper and crossflow lowers are compatible. I know that both changed driveshaft length in 1992, but do they have the same gear ratio and spline count? Bolt pattern appears to be the same.
  6. sutor623

    Merc v6 offshore 200 water pressure issue

    Hey guys, I am dealing with a head scratcher. A buddy of mine has a 1997 200 offshore 2 stroke carbed motor. Serial :OG487642 Anyways, he brought it to me to look at. He had overheated badly enough to melt the main wiring harness to the block. The impeller was shot and all of the fins were long...
  7. sutor623

    Help identifying prop pitch

    Hey guys i need to replace a prop on a 24’ Sweetwater Tri-toon. There are two numbers stamped on the side. 9602 and 5115. It is an aluminum prop on a 90hp Honda engine. I am guessing it is a 15 pitch but I’m not positive. Any insight would be greatly appreciated!!
  8. sutor623

    Honda prop Identification?

    Hey guys, I have a 24' sweetwater pontoon with an aluminum prop on a 90HP Honda. The prop has 2 numbers on it. one is 9602, the other is 5115. These are the only numbers I can see. I am trying to find the pitch because I need a new prop!!
  9. sutor623

    F150 loss of power up top

    Hey guys, long time no see. I am working on a 2010 Yamah F150TJR. Motor has been kept up with filter changes etc. Only run ethanol free gas from the marina. It is on a 24' tri-toon. It just started "starving" for fuel at upper rpms. Under that it seems ok at first. When you run it at 3000 rpms...
  10. sutor623

    Johnson GT 150 issues

    Got a 1987 GT150. Motor ran perfectly the first time we had it out. This was after I had put in a waterpump, rebuilt the carbs, new plugs etc. Well next time I had it out, at around 3000 rpms the motor would pick up to 3250rpms for a split second and then go back down to 3000. Like it’s...
  11. sutor623

    What size bolts for Yamaha 50hp flywheel?

    Hey guys, I have to pull a yamaha flywheel and put in a stator. Does anyone know the bolt thread count and size? Surely it is metric. Motor is a mid 90's 50hp 2 stroke oil injected. Thanks!!
  12. sutor623

    Help Locating main wiring harness part number

    Hey guys, Got a 2004 BF130. Engine is good to go but some muskrats chewed the main wiring harness in two about 3' back from the motor. I need to get the main wiring harness and the battery cable if anyone can help me locate the part numbers. They have a LOT of wiring harnesses in this motor...
  13. sutor623

    2011 F250 will not trim out under load

    Hey guys, Motor is a 2011 F250TUR I am working on this trim system. The unit will trim up and down as it is supposed to, and will not leak down when trimmed up and left up on the trailer. This trim system was having issues before the motor was transferred owners. The shop that sold this motor...
  14. sutor623

    Trying to free up piston rings.

    Been working on a 150GT and had to pull the exhaust cover to fix some small leaks. While I was in there I inspected the rings and cylinders. Pistons have minimal scuffing, bores look good with crosshatching still present. Starboard rings look excellent. There is no carbon present and the rings...
  15. sutor623

    150 GT torque specs

    I have an ‘86 150 GT and I had to replace the gaskets for the exhaust cover. Does anyone know the torque specs/sequence for the re-install? Does it need gasket sealing compound? Thanks!!
  16. sutor623

    Johnson GT150 voltage regulator issue?

    Hey guys got a 1986 Johnson GT150. She runs great. I know that these motors have the 30 amp charging system, but what kind of voltage should I have at idle? I am running 15v at idle and 15.5v at mid range rpms. The tach works perfectly and none of my wiring looks like it has gotten hot. Do I...
  17. sutor623

    V6 Crossflow VRO conversion

    Hey guys, I just got a 1987 Johnson GT150. Doing a cooing system and fuel system overhaul on her. I had a 1984 Evinrude 150 XP and it had the two fuel pumps, both with block mount pulse ports. I know a lot of these motors had the block mount port(s) as well as the pulse limiter port on it for...
  18. sutor623

    Help removing mildew/mold!!

    Hey fellas, Got a nice 24' pontoon. Put her away dry a few weeks back and my cover has failed, meaning moisture has gotten into the boat. Postponed winterization and am now regretting it. Anyways, I have starbrite mildew remover and CLR foaming mildew and mold remover, and neither of them will...
  19. sutor623

    Anyone use teleflex 4.2 NFB (No Feedback) steering?

    Hey folks, I have a 19' aluminum CC and I am putting a 2 stroke 150hp Johnson GT on there. I was wondering if a single cable NFB system would suffice? I can get a brand new system for $200. Id like to go hydraulic, but best price I can find for my particular engine is $650. Yikes!!
  20. sutor623

    Creating proper plywood thickness for transom?

    Hey guys, Got a bit of a conundrum that I am trying to work around. So I went to the wood distributor last week. I have a tinny I am restoring. I have a transom thickness of 1 3/4", and floors 3/4" thick. The supplier told me that they had marine grade douglas fir in 1" which actually measures...
Top