Search results

  1. labawg

    1984 Force 125hp Steering Tube

    Is the 1984 125hp Steering tube the same as later models (1985-1990)? Another question almost all third parties parts say for 1985 Force 125hp and later but nobody mentions the 1984 force 125hp. Is this an oversight or is it really different? I know from past experience most of the parts are the...
  2. labawg

    Convert Binacle Mount Control Box to work with Force Outboard

    Re: Convert Binacle Mount Control Box to work with Force Outboard Thanks Jerry and Frank. I now see that the Chrysler/Force uses a universal control cable set like the 3300 Xtreme Control Cable and the Chrysler & Force Teleflex Connection Kit CA27019 I think. So probably any universal...
  3. labawg

    Convert Binacle Mount Control Box to work with Force Outboard

    Has anyone done this yet. My current motor is a 1984 125hp with TT. Thanks for any help.
  4. labawg

    Manual Hydraulic steering

    Has anyone installed Manual Hydraulic steering StarStar or BayStar and how did you like it
  5. labawg

    Who made this boat?

    Wondering who made this? http://wausau.craigslist.org/boa/2656896361.html
  6. labawg

    Will 1992 Force 150 powerhead bolt to a 1984 Force 125 Leg?

    I know the upper and lower cowl will have to be changed to make room.
  7. labawg

    Painting 1984 Force Upper Cowl

    Took forever to remove foil decal from cowl and finally had to sand the remainder off but also sanded through the paint and primer on most of it. I believe the cowl is made of fiberglass or a type of plastic. What should I prime and paint it with since it is a little flexible?
  8. labawg

    Will this LU fit Force 1984 125 hp?

    Supposedly this LU came from a 1983 Force 125 hp. It has the two piece shaft and looks much later. By looking can anyone tell me is it will fit and does it have an 2:1 gear ratio?
  9. labawg

    How does a lean runup and Burbling sound?

    Unless your Frank or Jerry or one the Sages, it is hard to determine what things sound like. A example; you do a hole shot and the motor sounds rough until 3000 rpm and then zoom. FJS (meaning Frank, Jerry and Sages) can listen and say "Thats burbling" meaning its way rich and getting too much...
  10. labawg

    Drain, Fill, Vent Plug Seal 1984 Force 125 hp which one? Frank?, Jerry?

    Currently draining old milky lube from my LU. PO used Blue Permatex on all three, no seals. Can I just buy rubber orings or do I need to buy mercury/Sierra ones?
  11. labawg

    What the difference between fk10107 and fk10170 needle and Seat?

    What the difference between fk10107 and fk10170 needle and Seat?
  12. labawg

    Force two stage fuel pump check valves part number?

    Force, 1984, 125hp, fuel pump assy. Does anybody knows the part numbers of the first stage, center and second stage check valves?
  13. labawg

    Timing marks on 1984 125 hp Force motor

    Having read thread "1984 Chrysler 125 - at what revs is max advance?" I have a question on timing marks. My flywheel has only two marks. Is the first one(on the right) TDC and the second one(on the Left) 30 degree BTDC? This not shown in the Clymer for a 198? Force 125 hp motor.:confused:
  14. labawg

    Tilt Trim Sender unit for 1984 Force 125hp motor?

    Is FA455791 the correct one. My has 4552C6 on the casting but looks like (F)A455791. Also does anyone know the ohm values?
  15. labawg

    Rear Motor Leg cover Removal and Support Plate Removal on 1984 125 hp Force

    While not at the same time, after dropping the lower unit is it possible to remove the rear motor leg cover without pulling the powerhead? Different question, with everything in place is it possible to remove the support plate without pulling the powerhead? I have the Clymer but it's not clear...
  16. labawg

    Any Ideas about removing the foil decal on a 84 force outboard hood?

    I have tried a decal removing wheel and works great on other things but not this foil decal on the hood. How do others do this? I'm not sure where to post this but we'll start here. Thanks for any help.
  17. labawg

    Force 125 HP 1984 Bad Spark Plug Caps

    Are these zero ohms and if so are the NGK LZFH good enough? Best Regards
  18. labawg

    Force 125 HP 1984 with Black and Blue CDIs is there and issue?

    Have a Force 125 HP 1984 with 1 Black and 1 Blue CDI is this a problem? Once read you should use all Black or all Blue CDI units. Blue CDI has Blue coils and Black CDI has Black coils. I know you can use Blue CDI on Older Force motors but if mixing is an issues I have access to a new Blue CDI...
  19. labawg

    Fabricating a new transom out of 2? box aluminum tubing

    I?m thinking of Fabricating a new transom out of 2? box aluminum tubing for a 1984 Nordic CrestLiner 18ft boat. Has anyone done this before? Or is there a problem with this concept? Besst Regards Loren Gregg LaBaw
  20. labawg

    Is there a method to turn 18 ft boat upside down?

    Hi guys just purchased a 1984 Crestliner Nordic 18 ft aluminum boat that has tons of flaking paint everywhere on the hull. It looks like the last owner took a rattle can to it without prepping. I'm going to gut the boat but need instruction on how to turn it upside down to sand, prep, and paint...
Top