Search results

  1. H

    can anyone find me a prop

    1994merc. 4hp. Composite. I have called everyone I know. Even. Mercury. They say this is obsolete. No longer avibille
  2. H

    2008/4.3/ no fire?

    witch wire goes on the hot + side on a coil - purple or gray.
  3. H

    Broken skag

    A friend Hit something yesterday and broke almost 1/2 of the skag off ( the back half) must have hung the Log or big stick/ no prop damage. 75hp/merc/ about a 98yr md/ Now His boat will not plane off. Would the missing piece cause this? Prop still engages fine.( you can turn engine with it...
  4. H

    1999/ mercury/tracker 40 hp

    Trying to replace the Imp& shift shaft boot on this thing. where do you find part's for these cross breed motor's??? the sel# plate is faded so bad I cnn't read the # . DO i get merc. part's or force part's?
  5. H

    transom seal replacement

    I'm looking at buying An 1984 cheetah 166. It needs a new transom seal/boot. How hard is it to do/ I've never done one this old. IT's a older omc sterndrive
  6. H

    mercury parts express

    trying to find parts for my 96/115/elpto/og404452. But it say's it can't find my sel#. Were can i find daigram of what i need / lower unit part's
  7. H

    no fire

    94/seadoo gtx I put put new starter on it it ran 30 min and quite. Now it restated but ran 15-20 sec. and now i have no fire HOW do i ck the 4 wires comming out of the stator without pulling the flywheel. or what else do i need to CK frist
  8. H

    1982/9.9 johnson fuel pump

    friend of mine tryed to put fuel pump kit in and so i don't know how it came apart need a diagram. is there a link i can use?
  9. H

    outdrive/r/r

    i just got a 1988 glastron gx-219 -o/d sel 0c377755/ 260v8 alpha one and the shift bellows is bad. were can i get info on repair. and it does not have a exhust bellow. should it have one
  10. H

    Johnson firing trouble

    I have a 1999 Johnson 25 hp 3 cylinder. It started out quiting on me sometimes after running for about 30 to 45 mins. I have been running it on the hose and it started loosing fire on #2 cylinder. Then it lost fire on all 3 cylinders. Checked power going into all 3 coil packs (none). Checked...
  11. H

    johnson web site

    looking for a web site that has diagrams of johnny/rude motors
  12. H

    200hp merc starts then dies

    this is a 2000yr carb/200 hp it will start run 2 or 3 sec. and dies. I have checked fuel supply and it getting gas /it does not appear to me to have a real good spark. Some of the vac. lines were off and i am not sure they were put back right . Got to start somewhere ,any help i will try it ...
  13. H

    draining water for the winter

    trying to find the location of the drains on my 4.3 liter. How many are there and the location?
  14. H

    best way to remove VRO system

    94 evinrude 50hp VRO. I want to remove the lines and pump / can i just pull them all and install a elec. pump. I don't think the one on here is working right /it is filling carbs with oil and flooding real bad ,so i pulled the oil hose and hooked to a tank of 50/1 and it ran better
  15. H

    no fire on a 94/vro 50 hp

    well i took the merc off and set a 50hp vro on my daughters boat. Guess what? It has no fire at all. THE controls are the ones that it was running with /starter turns motor good , have 12+ volts on the 3 terminals at rear of treminal block , but no fire at plug wires . How should i CK stator...
  16. H

    75hp merc no spark on 3-4

    it is a 75 hp ser 6613843 don't know the yr but has a good spark on 1-2 nothing on 3-4. I moved the wires from #1 to all 4 coils and they spark good. what should i ck next
  17. H

    water in oil pan [2 gallon or more]

    A friend of mine got a real good deal on a 98 larson /4.3L-gl-b volvo. went out spent 1600 on int. before running. Now the bad part. he put it in for the frist time and it started blowing oil/water out the spark arrestor. He thinks it is just a head gasket. I am thinking much worse/new motor...
  18. H

    prep before paint

    After months of debate i have went to my local sherwin/willams dealer and got ms52 /ms5 hardener to recover red flake gelcoat. Now he says to clean /lac.thinner then 3m pad /and shot. I tryed a small place and it fish eyed. How should i prep? :confused: really
  19. H

    omc riser flap

    had the manifold off my 3.0 liter and the flaper in the riser is burned on one side /half of it is gone it is just hanging there on one side. should i replace it / or just run it like it is?
  20. H

    corner covers on pontoon

    the part that goes on a pontoon i have that covers the corners are all gone. What are they called and where might i find new ones :confused: :confused:
Top