Search results

  1. D

    Need HELP identifying motor first

    So it won’t start again according to the timing light and the marks on the fly wheel , it is in time . I have spark continually while cranking . I have replaced gas lines connectors , squeeze ball is hard . So I don’t know what else to do . I have posted a lot of infor Action so people who know...
  2. D

    Need HELP identifying motor first

    120 both
  3. D

    Need HELP identifying motor first

    There is 120 both cylinders here are the books one is a parts book The other thing I did tonight was I took off the fuel pump and just bypassed it to the carb manifold. And it ran again , ran like ****. Air screws on carbs are out 5 turns . At 3 or 3.5 or 4 or 4.5. Won’t run start die. I...
  4. D

    Need HELP identifying motor first

    I don’t want to jump all over the place on this topic . But can someone post a picture or the book number that should be using. So I have a fuel water separator just before the motor. Gas is fresh . I am scratching my head a lot . I will post compression numbers
  5. D

    Need HELP identifying motor first

    Thank you for the reply’s. No matter what I do I can’t get this to idle nicely or even good . It is a 2 stroke . lol. I looked under flywheel seal is not leaking . I have had the motor running and sprayed carb cleaner around motor looking for vacume leaks . Motor never sped up . The timer...
  6. D

    Need HELP identifying motor first

    So I posted some pictures, can you tell from them about what year or model ? Thanks Dale
  7. D

    Need HELP identifying motor first

    It’s in a barrel of water , what should the idle be in neutral
  8. D

    Need HELP identifying motor first

    If the flywheel key was sheered wouldn’t it be out of time for the magnets are telling the aystem When to fire properly ? As for holding the key in for the primer , at this time the primer is not hooked up. I have to replace seal . Don’t is Not on motor at this time .
  9. D

    Need HELP identifying motor first

    Sorry my phone goofs And posted twice .
  10. D

    Need HELP identifying motor first

    Sorry here are the two videos . Grabbed photos last 2
  11. D

    Need HELP identifying motor first

    Sorry here are the two videos . Grabbed photos last 2
  12. D

    Need HELP identifying motor first

    Sorry I lost the page , I book saved it now . I was told it was a 2002 ??? So last year the motor was running rough. So I decided to buy the repair manual . I am Mechanically inclined , so I also download a video from Brandon’s garage that shows you how to adjust the linkage back to factory...
  13. D

    Need HELP identifying motor first

    Sorry, did not know I did that .
  14. D

    Need HELP identifying motor first

    Forgot pictures
  15. D

    Need HELP identifying motor first

    Hello all, long story short, was told this was a 2002 Johnson . 50 hp bombider . The welsh plug is the only thing left for tag. I can add pictures if needed but here is a picture of the plug
  16. D

    Need HELP identifying motor first

    Hello all, long story short, was told this was a 2002 Johnson . 50 hp bombider . The welsh plug is the only thing left for tag. I can add pictures if needed but here is a picture of the plug
  17. D

    Mercury 1987 20hp will not run

    Yes I have , I have a 25 hp a little newer but same concept . So I switched coils and wires . Didnohma reading on stator and trigger . Stator seems to be a little lower . So I orderd a new one . But spark at coil does not reed high . Can someone tell me what type of voltage I should be looking...
  18. D

    Mercury 1987 20hp will not run

    Yes I have . No change . I even thought of maybe someone out the coil wires on wrong . So took off fly wheel and everything looks good under it. Did some readings off the stator. According to CDI BLACK /white to Brown/yellow should be 650-850 ohms . Mine reads 742 so good . Low speed should be...
  19. D

    Mercury 1987 20hp will not run

  20. D

    Mercury 1987 20hp will not run

    So I have a spare tester . I set it to 1 inch spacing and tested spark. Was all over , put it to 3/4 it was a lot better . I put a straw in cyl 1 turned it till it was TDC . Then I looked at the flywheel it was on the two dots so the book shows that as setting the base time. As for the link...
Top