Search results

  1. R

    1968 eska 7.0hp impeller change

    Hi all I need some advice please. Can anyone tell me how to change the impeller on this motor? The motor is fitted with a f/n clutch, so can I just drop the gearbox to access the impeller, or will the clutch parts stop the drive shaft dropping down the leg. Will I have to remove power head to...
  2. R

    Johnson 5 1/2 hp

    Hello folks. Just by pure chance I have bought a 1963 model CD-20 Johnson that has never been used. It has stood at the back of a garage since purchased and left for 49 years. It must have been run in the Canadian factory as there are slight traces of carbon on the piston crowns. The original...
  3. R

    Johnson/Mariner/Mercury 3.3hp are they any good?

    Hello folks I have been looking for a replacement engine for my trusty old 80s 4hp Evinrude,as it is now looking a bit "dated". The Johnson 3.3 looks light weight and more modern, I was going to buy a good used one untill I saw the on- line parts list. The motor only seems to have one piston...
  4. R

    remind me please

    Hello I need a new top crankshaft for my 71 mfd 4hp Evinrude. I just cant remember how to view the Evinrude/Johnson on line parts drawings at Iboats. Can you remind me please........yes it could be old age. Thanks
  5. R

    Merc 7.5 leaking fuel

    Hi Have recently bought a 1985 Merc 7.5. Runs fine, BUT when I squeeze the primer bulb on fuel line and the carb becomes full fuel spurts out of a hole on the front face of the carb. There are 3 holes,two look like they are for fitting an air filter but above the right hand hole there is...
  6. R

    Mercury 7.5 thermostat

    Hi all Anyone know where to find the thermostat on the Mercury 7.5hp? 1986 year. You know I just cant find it. Must be one somplace as they listed in the merc spares section. Any ideas folks? Thanks ray.
  7. R

    3hp Help please

    Hello all. I own two 3hp motors, a Johnson and a Gale. Both are used regularly and run very well,in fact I am a big fan of these motors This autumn I decided to strip both for de-coke,new impellers and check over. All was fine until I got to piston rings (bores/cylinders OK,only .001"clearance...
  8. R

    Gale outboard questions

    Hi I own a 1962 Gale Buccaneer 3 hp outboard,and am often ask questions about it, as they are not a common engine here in England. Where these engines offered for sale in the UK? If so why,as OMC had a factory in Belgium that built Johnson/Evinrude motors for the European market. Another...
  9. R

    Johnson/gale 3 hp

    Hi I have just bought a Gale buccaneer/Johnson 3 hp. Model#3B11C SER#B55409. Yes you know what I am going to ask! Anyone know the year of manufacture? Thank you Ray
  10. R

    66 Johnson 3hp bit more advice please

    Hello all. My 3hp Johnson seems to be running too hot when run in garbage can full of water to the correct height. After a few minutes running the cylinder head is hot enough to burn your fingers if you hold it for a few seconds. Have fitted new impeller,and checked pump housing for wear. Will...
  11. R

    60s Johnson paint color.

    Hello all. Can anyone tell me if the cream paint on 60s Johnson's has a near match in auto spray paint. Or if you have re sprayed a cream Johnson what color did you use? Thank you Ray:)
  12. R

    1966 Johnson 3hp quick question

    Hello all. on the motor swivel bracket there is a screw to adjust the friction when turning/steering motor. On mine the screw bears on the top plastic bush. Is this correct or do I have a missing part ? Seems like there should be something to prevent the screw chewing up the top bush. If there...
  13. R

    1966 Johnson 3hp advice please

    Hello all. I have bought a seized 66 johnson 3hp model JH21E C504192. I just love the design of these motors. The leg has been removed and drive shaft is free to turn prop. So I have removed the exhaust cover/plugs and can see pistons,all looks ok in cylinder bores,but the crank is solid,only...
  14. R

    Campari mk 25 outboard

    Hi I have recently been given a Campari mk 25 air cooled single cylinder 2 stroke motor as a none runner. After replacing the condencer the motor now runs good. I am guessing its around 1 1/2 hp. I can find no information about these motors on the internet,and was wondering if anyone on this...
  15. R

    6hp Power Outlet Wiring

    Hello Folks. I have a 6hp Evinrude 65B66R/B07044. This model is fitted with a rubber power outlet socket. I would like to use this socket but need some help. There are 3 wires to the socket feeding back up to charging coils under flywheel,so I guess I need a rectifier ? Have looked in faqs and...
  16. R

    Evinrude 6

    Hi Do any of you guys know if the engine fitted to the fisherman model is the same as my later 75 Evinrude 6hp? I have just finished rebuilding my motor(thanks to this forum and tashasdad) but thought I might pick up another motor for spares. I have spotted a fisherman short shaft for sale with...
  17. R

    My friends monkey

    EDIT (nasty)
  18. R

    6HP Evinrude-carb plugs-coil fitting.

    Hi I need a bit more advice about my little 1975 evinrude 6. When I refitted the carb I noticed that in the top of the carb near a blanking plate there are 3 holes,one into the slow speed needle casting,and another 2 along side. One of these holes is open and the other two have lead plugs,should...
  19. R

    Evinrude 6hp Year Of Manufacture.

    Hi My 6HP Evinrude has lost its information plate many moons ago. There are two sets of numbers stamped on the cylinder block freeze plug. BO 7044 and 65B66R. I have tried to match these up on the internet but with no luck. I would like to know when this engine was manufactured (Belgum) as I...
  20. R

    what is this?

    Hi all Anyone any idea what engine this is? For sale in our local vintage outboards section, but owner has no idea what it is.;)
Top