Search results

  1. C

    Outboard bracket mounting specifics - question

    Hello. I have a 26" setback, 17 degree angle, Stainless Marine brand bracket that is on a donor boat, which I am going to transplant to a 25 ft Aquasport center console (1979 246 CCP). I know that the cavitation plate has to be about 1 inch above the bottom of the boat for every foot of bracket...
  2. C

    Evinrude Johnson 1990 225 Looper LAST RESORT flywheel removal tip

    Re: Evinrude Johnson 1990 225 Looper LAST RESORT flywheel removal tip Here it is just as it finally cracked and released. I cut as much as I could with a cut off wheel but then I had to drill the rest with a cobalt bit. what a job! Here is the key. Everything looks fine. I cannot understand...
  3. C

    Evinrude Johnson 1990 225 Looper LAST RESORT flywheel removal tip

    Re: Evinrude Johnson 1990 225 Lopper LAST RESORT flywheel removal tip Re: Evinrude Johnson 1990 225 Lopper LAST RESORT flywheel removal tip Long bolt to act as stopper so flywheel wont spin Hole saw setup, notice no center drill bit. It took about 15 minutes. I would suggest vacuuming...
  4. C

    Evinrude Johnson 1990 225 Looper LAST RESORT flywheel removal tip

    Hello Everyone, I made a discovery today (i think??) that hopefully will save you alot of time someday. I restore late 80-early 90's crossflows and loopers as a hobby so I am quite familiar with them. Lets say i am a professional amateur. So I got this 1986 225 Looper. The scary thing was it was...
  5. C

    1991 Johnson 225 carb jetting

    Hello Guru's, I have a txeic, 1991 225 looper. I have one cylinder .030 over (#4 I believe). Should there be different jetting for that cylinder? and if so, Is it the corresponding carb that is right in front of it (not the opposite side like on crossflows?)? I have all #62 main jets, but the...
  6. C

    1991 225 blowing rectifiers

    Hello, I have a TXEIC, 1991 225, Johnson. for fun I buy tired motors and refurbush them... honed, new rings, all soft goods replaced, new check valves, etc. I am an advanced tinkerer and just short of professional. Ive refurbished about 9 early 90's loopers in the last 3 years. I feel I have...
  7. C

    Prop for 1988 Evinrude 175 on 20' center console

    I have a basic 1978 Aquasport 200ccp Center Console (no tee top or heavier equiptment) with a 1988 Evinrude 175. I just got the motor this season. It seems like the motor is straining and a bit bogged down in the upper rpms. twice the motor came to what seemed like a catastropic clanking stall...
  8. C

    converting 1988 150 to a 175-carb question

    Hello, took a evinrude 175 powerhead and put it on a 1988 150 body. I used everything off of the 150... carbs, electrical, etc. My question is can I use the "1 1/4" carbs off of the 150 and rejet them or does the 175 require the 1 3/8 carbs?
  9. C

    Evinrude 1986 225 Carb flat spot/stalling

    hello, I am stumped. I have a 1986 225... new stator, timing base, VRO pump and power packs, carbs rebuilt, good compression (almost 110 lbs per). It idles a bit rough at times and sneezes and sometimes stalls. This is corrected by bliping the choke a bit. Secondly when i throttle up, it will...
Top